background image

16.

17.

DERAILLEUR HANGER INSTALLATION

01. HANGER SEAT

02. HANGER CAP SEAT

Lightly grease the outside surface of the hanger 
where it interfaces with the frame. The hanger will 
fit into its space on the inside of the swing arm 
and should press easily into the frame.

Lightly grease the threads on the hanger cap.  
The hanger cap REVERSE threads into the 
hanger from the outside of the swing arm. Hand 
thread the cap into the hanger.

03.  TIGHTENING 

04. COMPLETED

Using a 6mm allen key, tighten the hanger cap 
into the hanger. REMEMBER, it is REVERSE 
THREADED. Follow the “Tighten” arrow on the 
cap. Finigh tightening with a torque wrench if 
available.  

*Torque to 80 in/lbs (9Nm)

The installed hanger and cap should look like this, 
sitting flush against the frame on both the inside 
and outside of the swing arm. If the hanger or cap 
are not sitting flush against the frame, remove 
them and inspect the frame surfaces for debris as 
well as the threads for damage.  

NOTE:  The hanger cap is REVERSE 
THREADED.  Be careful not to strip out the 
Hanger tool faces.  The cap is marked with a 
tighten direction arrow.

Inspect the frame around the hanger seat for 
any suspicious damage any time you replace 
a hanger, especially if you are replacing it due 
to damage.  

YETI TIPS

TOOLS NEEDED

• 6mm Allen key
• Grease

DERAILLEUR HANGER INSTALL

Summary of Contents for SB4.5


















Reviews: