3
P2: Auto
-
Shut
-
Off Time
•
From the parameter '
Set 1
' if the
'SET'
key is pressed once, the user
gets access to parameter
'Set 2'
. ’
SET 2
’
allows the user the ability to
adjust the auto
-
shut
-
off time. The
'UNIT'
key decreases the current
value and the
'FUNC'
key increases it.
•
The allowed values for this parameter are in the range from 1minute
to 30 minutes in 1 minute increments.
•
To disable this auto
-
off feature (turned on until a manual turn
-
off) the
user must increase or decrease the parameter value until the
'OFF'
value is displayed.
P3: Buzzer on Alarm Enable/Disable
•
From the parameter '
Set 2
' if the
'SET'
key is pressed once more, the
user gets access to parameter
'Set 3'
which allows the user the ability
to enable or disable the buzzer sound in case of an alarm.
•
Press the
'UNIT'
or the
'FUNC'
key to change the actual value.
•
The detector is set from the factory with the alarm buzzer enabled
(Set 3=On).
•
Pressing the
'SET'
key again will result in exiting the parameters
configuration mode. When exiting the detector will store all changes
in the detector
’
s memory as the preferences.
OVER
-
RANGE FUNCTION
•
This function
is
continuously
checking the measured
concentrations to verify that they remain within the detector
’
s full
range limits.
•
When the full range value is exceeded, the internal buzzer will start
beeping at the maximum repetition rate and the
'ALM'
symbol will
be turned on and the lower display will show the label
'OFL'
(overflow)
.
LOW BATTERY FUNCTION
•
The detector monitors the battery level and when it is below a
certain pre
-
set value, the low
-
level battery icon '
' is displayed
in the upper right side of the screen.
•
When this symbol is turned
-
on, the detector is still operational.
•
When the battery voltage falls below a critical level, the words
'Lo
Batt'
are shown on the display and the detector stops operation.
The only action allowed to the user is the turn
-
off.
•
When the detector is turned on again and the battery voltage is in
the valid range, all the functions are enabled.
•
For battery replacement please follow the directions explained in
the paragraph 'Beginning use'.
BUZZER
•
This detector has an internal buzzer for the indication of measured
concentration and as a sound feedback on some user actions.
•
When the detector is detecting a gas concentration greater than
zero, the rate of the 'beeps' increases according to the
concentration level.
SENSOR FAIL
•
The detector periodically checks the sensor status. When the
sensor is found to be defective, the buzzer sound is set to
continuous (when the Buzzer Alarm feature is Enabled) and the
words
'SEnS FAIL'
are shown on the display.
TECHNICAL FEATURES
Power supply:
9V, 6x1.5V AAA alkaline batteries
External power supply:
12 Vcc, 100 mA
Battery life:
4 hours minimum
Battery level:
6.00 V (instr. operational)
Low
-
Batt level:
5.50 V (instr. stopped)
Sensor type:
Semiconductor
Pre
-
heating time:
max. 45 seconds fixed
Auto
-
shut
-
off time:
OFF, 1
-
30 minutes
Display:
LCD TN
Protection grade:
IP 20
Operating temperature:
0°C .. +40°C
Storage temperature:
-
10°C .. +50°C
Humidity limits:
20% .. 80% RH
non condensating
Enclosure:
Material:
ABS HB self
-
extinguishing
Sensor Failure
When the detector sensor is found to be defective, the
buzzer sound is on continuously (when the Buzzer Alarm
feature is Enabled) and the words
'SEnS FAIL'
are shown
on the display.
1
Remove sensor sticker from protective cover at the end
of the wand (see figure 4)
2
Unscrew sensor protective cover
3
Pull sensor straight out
4
Align tab in end of the wand with the tab on the sensor
and insert sensor until fully seated
5
Screw on sensor protective cover
6
Apply new sensor sticker
7
Turn on unit and allow unit to heat and resume testing
Color: Blue
Dimensions: 2.8x5.9x1.5in (72 x 151 x 37mm). (W x H x D)
Weight: ~.7lbs (~ 312 gr.)
Sensor Wand Flexible Length: 10.6in (270 mm)
Accessories: External adaptor 230V~/12V= 100mA
(available upon request)
WARRANTY
The
Combustible Gas Leak Detector
is guaranteed for
12
months
from purchasing document date.
YELLOW JACKET
®
undertakes to repair or replace, free of
charge, those parts that, in its opinion, are found to be faulty
during the warranty period. The products which are found
defective during the above mentioned periods of time must
be delivered to YELLOW JACKET
®
postage paid. The
following cases are not covered by this warranty: accidental
breakage due to transport, inappropriate use or use that
does not comply with the indications in the product
’
s
instruction manual or quick start guide.
Any mistreatment, repairs and modifications to the product
not explicitly authorized by YELLOW JACKET
®
shall
invalidate the present warranty.
Contact YELLOW JACKET
®
Customer Service for a return
request form and shipping address.
Fig. 4:
Sensor change
Remove
sticker
and unscrew cap
to remove sensor
Ritchie Engineering Co./YELLOW JACKET
®
Customer Service:
1
-
800
-
769
-
8370 or
952
-
943
-
1300
Website:
yellowjacket.com
Summary of Contents for 69310
Page 1: ...1 Fig 1 Rev A P N 69310...
