Yealink W80 Administrator'S Manual Download Page 36

Page: 36 / 260

Managing the Handsets

Registering Handsets Time-Controlled
Registering Handsets at Once
Manually Closing the Registration

Registering Handsets Time-Controlled

A registration process is started automatically according to the time you set.

Procedure

Access the web user interface of the DM.

Go to

Handset & Account

Registration Center

In the

Registration Start Time

field, enter the time when the next registration process should be started.

Valid value: at least 1 minute later than the current time but no more than 24 days.

In the

Registration Duration

field, enter the duration that the DM should stay in registration mode.

Default: 3 minutes.

Click

Confirm

Related Topic

Manually Closing the Registration

Registering Handsets at Once

Procedure

Access the web user interface of the DM.

Go to

Handset & Account

Registration Center

In the

Registration Duration

field, enter the duration that the DM should stay in registration mode.

Default: 3 minutes.

Click

Start Now

The DM starts registration at once.

Related Topic

Manually Closing the Registration

Manually Closing the Registration

When the time is up, the system will automatically disable the registration status. You can also manually close the
registration.

Procedure

Click

Close

The screen prompts you whether to close the registration.

Click

Summary of Contents for W80





































































































































































































































































Search results

Summary of Contents for W80

Reviews:

Related manuals for W80

Brands by name

Popular brands

Yealink W80, Administrator'S Manual

Search results

Summary of Contents for W80

Reviews:

Related manuals for W80

Brands by name

Popular brands