Yealink W80 Administrator'S Manual Download Page 247 | Manualshive

Page: 247 / 260

background image

Troubleshooting Methods

244

1.

From the web user interface, navigate to

Settings

>

Configuration

.

2.

Click

Start

in the

Export All Diagnostic Files

field to begin capturing signal traffic.

The system log level will be automatically set to 6.

3.

Reproduce the issue.

4.

Click

Stop

in the

Export All Diagnostic Files

field to stop the capture.

The system log level will be reset to 3.

5.

Click

Export

to open the file download window, and then save the diagnostic file to your local system.

A diagnostic file named

<MAC>-DiagnoseInfo.tar

is successfully exported to your local system.

Note

: After exporting the diagnostic files, you can create a ticket to describe your problem at

ticket.yealink.com

, and Yealink

support team will help you locate the root cause.

Device Status

Available information on device status includes:

l

DM status (IPv4 status, firmware version, MAC address, machine ID and device certificate status, RFPI and net-
work information).

l

Handset status (handset model, hardware version, firmware version, IPUI code, SN code, and area).

l

Line status

l

Base Station Status (base station name, base status, MAC address, IPv4 address)

Topic

Viewing Device Status

Viewing Device Status

You can view device status via the handset user interface by navigating to

OK

>

Status

.

You can also view the device status via the web user interface.

Procedure

1.

Open a web browser on your computer.

2.

Enter the IP address in the browser’s address bar, and then press the

Enter

key.

For example, “http://192.168.0.10”.

3.

Enter the user name (admin) and password (admin) in the login page.

4.

Click

Login

to log in.

The device status is displayed on the first page of the web user interface.

Phone Reboot

You can reboot the IP phone remotely or locally.

Topics

Rebooting the IP Phone Remotely
Rebooting the Device via Web User Interface

Rebooting the IP Phone Remotely

You can reboot the phones remotely using a SIP NOTIFY message with “Event: check-sync” header. Whether the IP
phone reboots or not depends on “sip.notify_reboot_enable”. If the value is set to 1, or the value is set to 0 and the
header of the SIP NOTIFY message contains an additional string “reboot=true”, the phone will reboot immediately.

The NOTIFY message is formed as shown:

NOTIFY sip:<user>@<dsthost> SIP/2.0

«
...
245
246
247
248
249
...
»

Summary of Contents for W80





































































































































































































































































Reviews:

No comments

Related manuals for W80

ena Yealink SIP-T46S

Brand: Zayo Pages: 2

Brand: Feider Machines Pages: 16

Brand: Qwest Pages: 46

Brand: Uniden Pages: 32

Brand: AT&T Pages: 69

Brand: base engineering Pages: 26

Brand: Radio Shack Pages: 4

Commander M7310N

Brand: Nortel Pages: 4

Brand: Toshiba Pages: 16

Brand: Toshiba Pages: 16

Brand: Toshiba Pages: 24

Brand: Toshiba Pages: 16

Brand: Toshiba Pages: 24

Brand: Toshiba Pages: 23

Brand: Toshiba Pages: 16

Brand: Toshiba Pages: 16

Brand: Toshiba Pages: 22

Brand: Toshiba Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands