Yealink VCM36-W, Quick Start Manual

Page: 7 / 28

• Battery LED indicator:
Charging. Solid red
Slowly flashing red
Solid green for 3
seconds and then off
Fast flashing red 3
times and then off
The battery capacity is too low to power
on the VCM36-W.
The battery capacity is less than 20% .
The VCM36-W is standby.
Solid green
LED Status
Description
Fully charged.
The VCM36-W is powered on.
Solid green for one
second and then off
• The VCM36-W is in standby mode.
• The VCM36-W is powered off.
Off
4
Upgrading the VCM36-W
If the video conferencing system or UVC camera has a built-in wireless
microphone firmware after pairing with VCM36-W successfully, the VCM36-W
will be upgraded automatically.
Note: Make sure t he VCM36-W has enough power before upgrading.
E
N
G
L
I
S
H
Note: When the VCM36-W is not used for a while, it will enter standby
mode. You can wake up the VCM36-W by tapping the Mute button or
placing it in the charging cradle. After wake-up, the VCM36-W will
return to the state before standby.
Regulatory Notices
Operating Ambient Temperatures
• Operating temperature: +14 to 113°F (-10 to 45°C)
• Relative humidity: 5% to 90%, noncondensing
• Storage temperature: -22 to +158°F (-30 to +70°C)
Warranty
Our product warranty is limited only to the unit itself, when used normally in
accordance with the operating instructions and the system environment. We are not
liable for damage or loss resulting from the use of this product, or for any claim from
a third party. We are not liable for problems with Yealink device arising from the use
parties, etc., arising from the use of this product.
DC symbol
is the DC voltage symbol.
Restriction of Hazardous Substances Directive (RoHS)
This device complies with the requirements of the EU RoHS Directive. Statements
of compliance can be obtained by contacting support@yealink.com.
Safety Instructions
Save these instructions. Read these safety instructions before use!
The following basic safety precautions should always be followed to reduce risk of fire,
electrical shock, and other personal injury.
Environmental Requirements
• Place the product on a stable, level and non-slip surface.
• Do not place the product close to heat sources, in direct sunlight or next to
such as a microwave oven or a refrigerator.
• Do not allow the product to come into contact with water, dust and chemicals.
• Protect the product from aggressive liquids and vapors.
• Do not place the product on or near any inflammable or fire-
vulnerable object, such as rubber-made materials.
• Do not install the product in rooms with high humidity, for example, in
bathrooms, laundry rooms and wet basements.
Safety Notes During Operation
• Use only spare parts and accessories supplied or authorized by Yealink. The
operation of non-authorized parts cannot be guaranteed.
• Do not place heavy objects on top of the handset or the base station in case
of damage and deformation caused by the heavy load.
• Do not open the handset or the base station by yourself for repair purpose,
which could expose you to high votages. Have all repairs carried out by
authorized service personel.
• Do not let a child operate the product without guidance.
• Keep the small accessories contained in your product out of reach of small
children in case of accidental swallowing.
• Before plugging or unplugging any cable, make sure that your hands are
completely dry.
• Do not hold the handset up to your ear when speakphone is on or when the
ringer is ringing as the volumn can be very loud, which may be harmful to
your hearing.
• During a thunderstorm, stop using the product and disconnect it from the
power supply to avoid lightning strike.
• If the product is left unused for a rather long time, disconnect the base station
from the power supply and unplug the power adapter.
• When there is smoke emitted from the product, or some abnormal noise or
smell, disconnect the product from the power supply, and unplug the power
adapter immediately.
• Remove the electrical cord from an outlet by pulling gently on the power
adapter, not by pulling the cord.
Battery Precautions
• Do not immerse the battery into water, which could short-circuit and damage
the battery.
• Do not expose the battery to an open flame or leave the battery where it
could be subjected to extremly high temperatues, which could cause the
battery to explode.
• Do power the handset off before removing the battery.
• Do not try to use the battery for the power supply of any device other than
this handset.
• Do not open or mutilate the battery, released electrolyte is corrosive and may
cause damage to your eyes or skin.
• Use only the rechargeable battery pack delivered with the handset or those
rechargeable battery packs expressly recommended by Yealink.
• Defective or exhausted battery should never be disposed of as municipal
waste. Return old battery to the battery supplier, a licensed battery dealer or
a designated collection facility.
Notices of Cleaning
• Before cleaning the base station, stop using it and disconnect it from the
power supply.
• Remove the battery before cleaning the handset to reduce risk of electric
shock.
• Only clean your product with a piece of slightly moist and anti-static cloth.
• Keep the power plug clean and dry. Using a dirty or wet power plug may lead
to electric shock or other perils.
(19,5210(17$/5(&<&/,1*
Never dispose of the device with domestic waste
Ask your Town Council about how to dispose of it in an environmentally
friendly way. The cardboard box, plastic packaging and player components
may be recycled in accordance with prevailing recycling regulations in
your country.
Always adhere to prevailing regulations
the law. The crossed out garbage can that appears on the device means
that when it has reached the end of its useful life, it should be taken to
a special waste disposal center and treated separately to general urban
waste.
Batteries: Be sure that the batteries have been placed in the right position. This phone
use rechargeable batteries only.
Compulsory information according to regulations for battery-operated devices.
Caution: Risk of explosion if battery is replaced with a battery of a wrong kind. Dispose
of batteries in accordance with the instructions.
Troubleshooting
The unit cannot supply power to Yealink device.
There is a bad connection with the plug.
1. Clean the plug with a dry cloth.
2. Connect it to another wall outlet.
The usage environment is out of operating temperature range.
1. Use in the operating temperature range.
The cable between the unit and the Yealink device is connected incorrectly.
1. Connect the cable correctly.
You cannot connect the cable properly.
1. You may have connected a wrong Yealink device.
2. Use the correct power supply.
Some dust, etc., may be in the port.
1. Clean the port.
Contact your dealer or authorized service facility for any further questions.
Contact Information
YEALINK NETWORK TECHNOLOGY CO.,LTD.
309, 3rd Floor, No.16, Yun Ding North Road, Huli District, Xiamen City, Fujian, P.R.C
YEALINK (EUROPE) NETWORK TECHNOLOGY B.V.
Strawinskylaan 3127, Atrium Building, 8th floor, 1077ZX Amsterdam, The
Netherlands
YEALINK (USA) NETWORK TECHNOLOGY CO., LTD.
999 Peachtree Street Suite 2300, Fulton, Atlanta, GA, 30309, USA
Made in China