background image

VC110 Video Conferencing Endpoint Introduction

 

This chapter contains the following information about VC110 video conferencing 
endpoint: 

 

VoIP Principles 

 

Physical Features of Endpoint 

 

Packaging Contents 

 

Endpoint Component Instructions   

 

Icon Instructions 

 

LED Instructions 

 

User Interfaces 

VoIP 

VoIP (Voice over Internet Protocol) is a technology that uses the Internet Protocol instead 
of traditional Public Switch Telephone Network (PSTN) technology for voice 
communications. 

It is a family of technologies, methodologies, communication protocols, and 
transmission techniques for the delivery of voice communications and multimedia 
sessions over IP networks. The H.323 and Session Initiation Protocol (SIP) are two 
popular VoIP protocols that are found in widespread implementation. 

H.323 

H.323 is a recommendation from the ITU Telecommunication Standardization Sector 
(ITU-T) that defines the protocols to provide audio-visual communication sessions on 
any packet network. The H.323 standard addresses call signaling and control, 
multimedia transport and control, and bandwidth control for point-to-point and 
multi-point conferences. 

It is widely implemented by voice and video conference equipment manufacturers, is 
used within various Internet real-time applications, such as GnuGK and NetMeeting, 
and is widely deployed by service providers and enterprises for both voice and video 
services over IP networks. 

 

 

Summary of Contents for VC110













































































































































































































































































Reviews: