background image

 

 

 

 

Quick Start Guide 

 

Media IP Phone – SIP-T52S 

 

 

STARTUP 

After the IP phone is connected to the network and supplied 
with power, it automatically begins the initialization process. 
After startup, the phone is ready for use. You can configure the 
phone via web user interface or phone user interface. 
 

CONFIGURING YOUR PHONE 

CONFIGURING VIA WEB USER INTERFACE  

Accessing the web user interface:  

1. Press the 

OK

 key when the phone is idle to obtain the IP address of the phone.  

2. Open a web browser on your computer, enter the IP address into the address bar  

    (e.g., "http://192.168.0.10" or "192.168.0.10"), and then press the 

Enter

.  

3. Enter the user name (default: admin) and password (default: admin) in the login page and click 

Confirm

Network Settings:

 

Click on 

Network

->

Basic

->

IPv4 Config 

You can configure the network settings in the following ways: 

DHCP

: By default, the phone attempts to contact a DHCP server in your network to obtain its valid network 

settings, e.g., IP address, subnet mask, gateway address and DNS address. 

Static IP Address

: If the phone cannot contact a DHCP server for any reason, you need to configure the 

IP address, subnet mask, gateway address, primary DNS address and secondary DNS address for the phone 

manually. 
 

Note: 

 

The IP phone also supports IPv6, but IPv6 is disabled by default. 

 

Wrong network settings may result in inaccessibility of the phone and may have an impact on 

the network performance. Contact your system administrator for more information. 

 
Account Settings:

 

Click on

 

Account

->

Register

->

Account X 

(X=1, 2, 3...11, 12) 

 

Parameters of the account: 

Register Status:   It shows the register status of the current account.   
Line Active:  

You can select Enabled/Disabled to enable/disable the account. 

Label: 

 

It is shown on the LCD screen to identify the account. 

Display Name:  

It is shown as Caller ID when placing a call.   

User Name:  

It is provided by ITSP for registration (required). 

Register Name:   It is an authenticated ID for authentication provided by ITSP (required). 
Password:  

It is provided by ITSP for registration (required). 

Server Host: 

It is provided by ITSP for registration (required). 

 

 

Summary of Contents for SIP-T52S












Reviews: