Yealink MeetingSpace VC200 Page 71 Administrator'S Manual Download

Page: 71 / 232

| Configuring Network Settings |

Data QoS

To ensure better presentation, data packets (PC content) emanated from the system should be configured with a high

transmission priority. DSCPs for audio, video and data packets can be specified respectively.
•

Configuring QoS

Configuring QoS

Procedure

Do one of the following:
• On your web user interface, go to

Network

Advanced

QoS

• On your VCS:

For VC880/VC800/VC500/PVT980/PVT950, go to

More

Setting

Advanced

Advanced Network

QoS

On your VC200, go to

More

Network

Wired Network

Advanced Network

QoS

On your VP59, tap

Setting

Advanced

Advanced Network

QoS

• On your CTP20, tap

Setting

Advanced

Advanced Network

QoS

Configure and save the following settings:

Parameter

Description

Configuration Method

QoS

Enable or disable the QoS

feature.

Note

: the default value is Off.

If you change this parameter, the

system will reboot to make the

change take effect.

Web user interface
Endpoint
CTP20

Audio Priority

Configure the DSCP

(Differentiated Services Code

Point) for audio packets.

Note

: the default value is 63.

The greater the number is, the

higher the priority is. If you

change this parameter, the

system will reboot to make the

change take effect.

Web user interface
Endpoint
CTP20

Video Priority

Configure the DSCP

(Differentiated Services Code

Point) for video packets.

Note:

the default value is 34.

The greater the number is, the

higher the priority is. If you

change this parameter, the

system will reboot to make the

change take effect.

Web user interface
Endpoint
CTP20

Summary of Contents for MeetingSpace VC200









































































































































































































































Search results

Summary of Contents for MeetingSpace VC200

Reviews:

Related manuals for MeetingSpace VC200

Brands by name

Popular brands

Yealink MeetingSpace VC200, Administrator'S Manual

Search results

Summary of Contents for MeetingSpace VC200

Reviews:

Related manuals for MeetingSpace VC200

Brands by name

Popular brands