manualshive.com logo in svg

Yealink MeetingEye 400, Administrator'S Manual, Page: 256 / 278

Share
Download
Yealink MeetingEye 400 Administrator'S Manual Download Page 256

 | System Maintenance | 

256

For VC880/VC800/VC500/VC200/PVT980/PVT950, go to 

More

 > 

Setting

 > 

Advanced

 > 

Reboot &

Reset

 > 

Reboot

.

For VP59, 

Setting

 > 

Advanced

 > 

Reboot & Reset

 > 

Reboot

.

•

On your CTP20, tap 

 > 

Setting

 > 

Advanced

 > 

System

 > 

Reboot & Reset

 > 

Reboot

.

It prompts whether you are sure reboot.

2.

Confirm the action.

Resetting the SD card of MeetingEye 600/MeetingEye 400/VC200/VP59

You can reset SD card (local storage) of MeetingEye 600/MeetingEye 400/VC200/VP59 to clear all
captured screenshots or recorded videos.

Procedure

1.

Do one of the following:

• On your web user interface, go to 

Setting

 > 

Upgrade

 > 

Reset Built-in SD Card

.

• On your VCS,

For MeetingEye 600/MeetingEye 400, go to 

More

 > 

Setting

 > 

Advanced

 > 

System Settings

 >

Reboot & Reset

 > 

Reset Built-in Setting Card

.

For VC200, go to 

MoreSetting

 > 

Advanced

 > 

Reboot & Reset

 > 

Reset Built-in SD Card

.

For VP59,  

Setting

 > 

Advanced

 > 

Reboot & Reset

 > 

Reset Built-in SD Card

.

The page prompt whether or not you are sure to reset.

2.

Confirm the action.

Resetting the System

Generally, some common issues may occur while using the system. You can reset your system and
camera to factory configurations after you have tried all troubleshooting suggestions.

•

Resetting the System via Configuration Methods

•

Resetting the System by using Reset Button

•

Resetting VP59 by REDIAL key

Resetting the System via Configuration Methods

Procedure

1.

Do one of the following:

• On your web user interface, go to 

Setting

 > 

Upgrade

 > 

Reset to Factory Setting

.

• On your VCS,

For MeetingEye 600/MeetingEye 400, go to 

More

 > 

Setting

 > 

Advanced

 > 

System Settings

 >

Reboot & Reset

 > 

Reset

.

For VC880/VC800/VC500/VC200/PVT980/PVT950, go to 

More

 > 

Setting

 > 

Advanced

 > 

Reboot &

Reset

 > 

Reset

.

For VP59, 

Setting

 > 

Advanced

 > 

Reboot & Reset

 > 

Reset

.

•

On your CTP20, go to 

 > 

Setting

 > 

Advanced

 > 

System

 > 

Reboot & Reset

 > 

Reset

.

Summary of Contents for MeetingEye 400























































































































































































































































































Reviews:

No comments