background image

13

O R I G I N A L   I N S T R U C T I O N S

EN

sand wood.

Move the sander towards and away from you, and gradually to a side. Wood should be sanded along the rings. Sanding should 

be started with coarser sandpaper; then the 

fi

 ner-grit sandpaper should be used gradually until achieving the desired e

 ect. Avoid 

checking the condition of the machined wood surface with a bare hand. This can cause injury from splinters and burrs formed 

during processing. Do not stop the sander in one place; this will cause uneven work results. Do not apply excessive pressure on 

the sanded surface during sanding. The pressure should be uniform throughout the entire working time. The sander should be 

guided in such a way that the sanding sheet adheres to the sanded object with the entire surface. Do not press the sander against 

the machined surface too hard. Excessive pressure can cause the sander to overheat and damage the machined surface and 

even to tearing of the sanding sheet or damage the tool plate.   

The sandpaper grit size must be selected according to the processed surface. Too coarse sanding sheets will produce scratches 

on the surface of the processed material. 

Take regular breaks during operation to check the condition of the sanding sheet. If a sanding sheet is found to have been clogged 

with dust generated during work, or that the abrasive grain has worn, replace the sheet with a new one. 

MAINTENANCE AND OVERHAUL

ATTENTION! Before any adjustment, technical service or maintenance operations unplug the tool. Once the operations have been 

fi

 nished, the technical conditions of the tool must be assessed by means of external evaluation and inspection of the following 

elements: body and handle, conductor with a plug and de

fl

 ection, functioning of the electric switch, patency of ventilation slots, 

sparking of brushes, noise level of functioning of bearings and gears, start-up and smoothness of operation. During the guarantee 

period, the user cannot dismantle the electric tools or change any sub-assemblies or elements, since it will cancel any guarantee 

rights. All irregularities detected at overhaul or during functioning of the tools are a signal to have the tool repaired at a service 

shop. Once the functioning has been concluded, the casing, ventilation slots, switches, additional handle and protections must be 

cleansed with a stream of air (at a pressure not exceeding 0.3 MPa), with a brush or a cloth without any chemical substances or 

cleaning liquids. Tools and handles must be cleansed with a clean cloth.

Summary of Contents for YT-82751













































































Reviews: