YASKAWA U1000 iQpump Drive, Technical Manual

Page: 563 / 706

B.12 o: Operator-Related Settings
The o parameters set up the digital operator displays.
u
o1: Digital Operator Display Selection
No.
(Addr.
Hex)
Name LCD Display Description Values Page
o1-01
(0500) Drive Mode Unit
Monitor Selection
User Monitor Sel
All Modes
Switches the display after the power has been turned on.
When using an LED operator, pressing the up arrow key will
display the following data: frequency reference → rotational
direction → output frequency → output current → output voltage
→ U1- oo .
Note: Enter the “1- oo ” portion of “U1- oo ” to view
the monitor. Certain monitors are not available in
all control modes.
Default: 106
(Monitor
U1-06)
Range: 104 to
914
344
o1-02
(0501) User Monitor Selection
after Power Up
Power-On Monitor
1: Frequency Ref
2: FWD/REV
3: Output Freq
4: Output Current
5: User Monitor
All Modes
Selects the information displayed on the digital operator when
the power is turned on.
1: Frequency reference (U1-01)
2: Direction
3: Output frequency (U1-02)
4: Output current (U1-03)
5: User-selected monitor (set by o1-01)
Default: 1
Range: 1 to 5
344
o1-03
(0502)
Digital Operator Display
Selection
Display Unit Sel
0: 0.01 Hz
1: 0.01 %
2: r/min
3: User Units
All Modes
Sets the units the drive should use to display the frequency
reference and motor speed monitors.
0: 0.01 Hz
1: 0.01% (100% = E1-04)
2: r/min (calculated using the number of motor poles setting in
E2-04, E4-04, or E5-04)
3: User-selected units (set by o1-10 and o1-11)
Default:
<1>
Range: 0 to 3
344
o1-04
(0503) V/f Pattern Display Unit
V/f Ptrn Unit
0: Hertz
1: RPM
V/f
OLV/PM
V/f w PG
AOLV/PM
OLV
CLV/PM
CLV
AOLV/PM CLV/PM
CLV
0: Hz
1: r/min
Default:
<1>
Range: 0, 1
345
o1-05
(0504) LCD Contrast Control
LCD Contrast
All Modes
Sets the contrast of the LCD operator.
Default: 3
Min.: 0
Max.: 5
345
o1-10
(0520)
User-Set Display Units
Maximum Value
UserDisp Scaling
All Modes
These settings define the display values when o1-03 is set to 3.
o1-10 sets the display value that is equal to the maximum output
frequency.
o1-11 sets the position of the decimal position.
Default:
<2>
Range: 1 to
60000
345
o1-11
(0521)
User-Set Display Units
Decimal Display
UserDisp Dec Sel
Default:
<2>
Range: 0 to 3
345
<1> Default setting is determined by parameter A1-02, Control Method Selection.
<2> Default setting is determined by parameter o1-03, Digital Operator Display Selection.
u
o2: Digital Operator Keypad Functions
No.
(Addr.
Hex)
Name LCD Display Description Values Page
o2-01
(0505)
LOCAL/REMOTE Key
Function Selection
LO/RE Key
0: Disabled
1: Enabled
All Modes
0: Disabled
1: Enabled. LO/RE key switches between LOCAL and REMOTE
operation.
Default: 1
Range: 0, 1
345
o2-02
(0506)
STOP Key Function
Selection
Oper STOP Key
0: Disabled
1: Enabled
All Modes
0: Disabled. STOP key is disabled in REMOTE operation.
1: Enabled. STOP key is always enabled.
Default: 1
Range: 0, 1
346
B.12 o: Operator-Related Settings
YASKAWA ELECTRIC SIEP C710636 04D U1000 Industrial MATRIX Drive Technical Manual 563
B
Parameter List