manualshive.com logo in svg

YASKAWA SI-EN3, Technical Manual, Page: 60 / 69

Share
Download
YASKAWA SI-EN3 Technical Manual Download Page 60

60

YASKAWA ELECTRIC

 SIEP C730600 92A YASKAWA AC Drive Option SI-EN3 Technical Manual

13  Troubleshooting

13

Troubleshooting

Drive-Side Error Codes

Drive-side error codes appear on the drive digital operator. 

Table 15

 lists causes of the errors and possible corrective 

actions. Refer to the drive Technical Manual for additional error codes that may appear on the drive digital operator.

Faults

Both bUS (Option Communication Error) and EF0 (Option Card External Fault) can appear as an alarm or as a fault. 
When a fault occurs, the digital operator ALM LED remains lit. When an alarm occurs, the ALM LED flashes.

If communication stops while the drive is running, use the following questions as a guide to help remedy the fault:

• Is the option properly installed?
• Is the communication line properly connected to the option? Is it loose?
• Is the controller program working? Has the controller/PLC CPU stopped?
• Did a momentary power loss interrupt communications?

Table 15  Fault Display and Possible Solutions

Digital Operator Display

Fault Name

bUS

Option Communication Error

• After establishing initial communication, the connection was lost.
• Only detected when the run command or frequency reference is assigned to the option 

(b1-01 = 3 or b1-02 = 3).

Cause

Possible Solution

No signal was received from the PLC.

• Check for faulty wiring.
• Correct any wiring problems.

Faulty communications wiring.
An existing short circuit or communications 
disconnection.

Check disconnected cables and short circuits and repair as needed.

A data error occurred due to electric interference.

• Counteract noise in the control circuit, main circuit, and ground wiring.
• If a magnetic contactor is identified as a source of noise, install a surge absorber to the 

contactor coil.

• Use only recommended cables or other shielded line. Ground the shield on the controller side 

or the drive input power side.

• Separate all communication wiring from drive power lines. Install an EMC noise filter to the 

drive power supply input.

• Counteract noise in the master controller (PLC).

The option is not properly connected to the drive. Reinstall the option.
Option is damaged.

If there are no problems with the wiring and the error continues to occur, replace the option.

Connection Time-out

The option Requested Packet Interval (RPI) timer timed out

Duplicate IP Address

Check if the option shares IP Address with at least one other node.
Check the setting values of F7-01 to F7-04 (IP Address).

Digital Operator Display

Fault Name

EF0

Option Card External Fault
The alarm function for an external device has been triggered.

Cause

Corrective Action

An external fault was received from the PLC.

1. Remove the cause of the external fault.
2. Reset the external fault input from the PLC.

Problem with the PLC program

Check the PLC program.

PLC is in the Idle Mode.

1. Set the PLC to the Run Mode
2. Set the parameter F6-54 = 0 (Enabled) to ignore errors while the PLC is in the Idle Mode.

EtherNet_conditional_E.book  60 ページ  ２０１６年６月２８日　火曜日　午後１１時３０分

Summary of Contents for SI-EN3






































































Reviews:

No comments