7 Parameter Table
YASKAWA ELECTRIC
TOEP C710656 09D YASKAWA Power Regenerative Unit - R1000 Quick Start Guide
29
U4-05
(7CH)
Capacitor
Maintenance
Displays main circuit capacitor usage time
as a percentage of their expected
performance life. Parameter o4-05 can be
used to reset this monitor.
Replace the capacitor when this monitor
reaches 90%.
U4-06
(7D6H)
Soft Charge
Bypass Relay
Maintenance
Displays the soft charge bypass relay
maintenance time as a percentage of its
estimated performance life. Parameter
o4-07 can be used to reset this monitor.
Replace the soft charge bypass relay when
this monitor reaches 90%.
U4-08
(68H)
Heatsink
Temperature
Displays the heatsink temperature.
U4-09
(5EH)
LED Check
Lights all segments of the LED to verify
that the display is working properly.
U4-13
(7CFH)
Peak Hold
Current
Displays the highest current value that
occurred during run.
U6: Operation Status Monitors
U6-80 to
U6-99
(7B0H
to
7F9H)
Option Monitors
1 to 20
Shows the monitor information for Option
Monitor 1 (876 Hex) to 20 (8FF Hex).
This information is displayed when option
cards are connected.
200 V Class: 100% = 400 Vdc
400 V Class: 100% = 800 Vdc
U9: Operation Status Monitors
U9-04
(823H)
Regenerative
Power (GWh)
Shows the total amount of regenerated
power.
U9-05
(824H)
Regenerative
Power (MWh)
U9-06
(825H)
Regenerative
Power (kWh)
U9-11 to
U9-14
(82AH
to
82DH)
Regenerative
Power Rates 1 to
4
These parameters show the regenerative
power rate in Power Unit Price (o4-19)
that is calculated from the total electrical
power consumptions in U9-04 to U9-06.
The unit price is set in o4-19, and U9-11 to
U9-14 are U9-04 to U9-06 times o4-19.
DI/DO Sel.
Description
Digital Input Function Selections
1
LOCAL/REMOTE selection
8
Baseblock command (N.O.)
9
Baseblock command (N.C.)
C
Analog terminal input selection
F
Through mode
14
Fault reset
18
Timer function input
1B
Program lockout
24 to 27
2C to 2F
External fault
No.
(Addr.
Hex)
Name
Description
000 000 000 kWh
U9-06
U9-05
U9-04
000 000 000 000
U9-14
U9-13
U9-12
U9-11
3C
Forced operation command
3D
Automatic operation command
47
Node setup
67
Communications test mode
Digital Output Function Selections
0
During run
6
Operation ready
7
DC bus undervoltage
8
During baseblock (N.O.)
E
Fault
F
Through mode
10
Minor fault
11
Fault reset command active
12
Timer output
1B
During baseblock (N.C.)
1D
During regeneration
1E
Restart enabled
20
Heatsink overheat (oH) pre-alarm
24
Fuse blowout detection
25
During run 1
26
During MC on
27
Overload (oL2) warning
2F
Maintenance period
3A
kWh monitor pulse output
3B
Alarm 2
3C
LOCAL/REMOTE status
4D
oH Pre-alarm time limit
60
Internal cooling fan alarm
100 to 160 Function 0 to 60 with inverse output
DI/DO Sel.
Description
D1000R1000_QSG_E_conditional.book 29 ページ 2018年2月26日 月曜日 午後2時38分