YASKAWA GA800 Series, Technical Reference

Page: 205 / 1016

Startup
Procedure
and
T
est
Run
4
4.10 Fine Tuning during Test Runs (Adjust the Control Function)
YASKAWA SIEPC71061737B GA800 Drive Technical Reference 205
Issue Parameter Number Possible Solutions Default Recommended Setting
Hunting or oscillation C5-06 [ASR Delay Time]
*1
• If torque or speed response are
slow, decrease the setting value
in increments of 0.010.
• If the rigidity of the machine is
unsatisfactory and vibration is
possible, increase the setting
value.
0.004 s 0.004 s to 0.020 s
• The volume of the motor
excitation sound is too high.
•
Hunting or oscillation at low
speeds (3 Hz or lower)
C6-02 [Carrier Frequency
Selection]
•
If the volume of the motor
excitation sound is too high,
increase the carrier frequency.
•
If hunting or oscillation occur at
low speeds, decrease the carrier
frequency.
1 (2.0 kHz)
*2
2.0 kHz to upper limit value
*1 Refer to the section on C5-xx parameters for more information about speed control (ASR).
*2 The default setting changes when the settings for C6-01 [Normal / Heavy Duty Selection] and o2-04 [Drive Model (KVA) Selection]
change.
◆
Advanced Open Loop Vector Control Method
Table 4.20 Parameters for Fine Tuning the Drive (AOLV)
Issue Parameter Number Possible Solutions Default Recommended Setting
•
oS [Overspeed] occurs.
• Hunting or oscillation.
T1-01 [Auto-Tuning Mode
Selection]
•
Make sure that the output of the
drive and the motor are
connected correctly.
•
Do Rotational Auto-Tuning for
a single motor.
- 0
The volume of the motor
excitation sound is too high. C6-02 [Carrier Frequency
Selection]
If the volume of the motor
excitation sound is too high,
increase the carrier frequency.
1 (2 kHz)
*1
1 to upper limit value
Speed precision is unsatisfactory E2-02 [Motor Rated Slip]
•
Decouple the motor and
machine and do Rotational
Auto-Tuning.
•
If the motor speed is slow,
increase the value of
E2-02 in
small increments
(approximately 0.1% of the
default setting value).
•
If the motor speed is fast,
decrease the value of
E2-02 in
small increments
(approximately 0.1% of the
default setting value).
*2
Set to a value that is ±5% of the
current value.
• Unsatisfactory motor torque
and speed response
•
Hunting or oscillation
• High speed
C5-01 [ASR Proportional Gain
1]
• Low speed
C5-03 [ASR Proportional Gain
2 (P)]
*3
•
If torque or speed response are
slow, increase the setting value
in increments of 5.00.
•
If hunting or oscillation occur,
decrease the setting value.
• C5-01 = 10.00
• C5-03 = 20.00
10.00 - 50.00
• High speed
C5-02 [ASR Integral Time 1]
•
Low speed
C5-04 [ASR Proportional Gain
2 (P)]
*3
• If torque or speed response are
slow, decrease the setting
value.
• If hunting or oscillation occur,
increase the setting value.
0.500 s 0.300 s to 1.000 s
The drive cannot find speed
response for low speed or high
speed.
• C5-07 [ASR Gain Switchover
Frequency]
*4
•
High speed
C5-01 [ASR Proportional Gain
1]
C5-02 [ASR Integral Time 1]
• Low speed
C5-03 [ASR Proportional Gain
2 (P)]
*3
C5-04 [ASR Integral Time 2]
Change the ASR proportional gain
and ASR integral time to conform
to the output frequency.
• C5-07 = 0.0 Hz
• C5-01 = 10.00
• C5-02 = 0.500 s
• C5-03 = 20.00
• C5-04 = 0.500 s
C5-07: 0.0 to maximum output
frequency
Hunting or oscillation C5-06 [ASR Delay Time]
*4
•
If torque or speed response are
slow, decrease the setting value
in increments of 0.010.
•
If the rigidity of the machine is
unsatisfactory and vibration is
possible, increase the setting
value.
0.004 s 0.004 s to 0.020 s
*1 The default setting changes when the settings for C6-01 [Normal / Heavy Duty Selection] and o2-04 [Drive Model (KVA) Selection]
change.
*2 The default setting changes when the setting for o2-04 [Drive Model Selection] changes.