YASKAWA FSDrive-MV1000 Series, Parameter Manual

Page: 163 / 241

2.6 F: Option Settings
YASKAWA ELECTRIC TOEP C710687 03B FSDrive-MV1000 Parameter Guide 163
2.6 F: Option Settings
u
F1: PG Speed Control Card Settings
Yaskawa offers a PG-X3 and PG-B3 motor encoder PG option card. Use the CN5-C port when using only one PG option
card and use the CN5-C and CN5-B ports when using two PG option cards. When programming one of the contact input
to act as a switch between two motors (H1-
†† = 16), use the card connected to port CN5-C for motor 1 and use the card
connected to CN5-B for motor 2.
Table 2.19 lists the parameters that must be set for each option card port.
Table 2.19 Option Card Ports and Corresponding Parameters
n
F1-01, F1-31: PG 1 and PG 2 Pulses Per Revolution
Sets the number encoder number of pulses per revolution.
n
F1-02, F1-14: PG Open (PGo) Circuit Operation Selection, Detection Time
A PGo fault is triggered if the drive receives no pulse signal for longer than the time set in F1-14. The stopping method
when PGo occurs should be set to parameter F1-02.
Parameter F1-02 Settings:
Setting 0: Ramp to stop (uses the deceleration time set to C1-02)
Setting 1: Coast to stop
Setting 2: Fast Stop (uses the Fast Stop time set to C1-09)
Setting 3: Alarm only
Setting 4: No alarm display
Note: Due to potential damage to motor and machinery, the “Alarm only” and “No alarm display” setting should be used only under
special circumstances.
n
F1-03, F1-08, F1-09: Overspeed (oS) Operation Selection, Detection Level, Delay Time
An overspeed error (oS) is triggered when the speed feedback exceeds the value set in F1-08 for longer than the time set
in F1-09. The stopping method when an overspeed fault occurs can be selected in parameter F1-03.
Port Parameters
CN5-C and CN5-B
(common)
F1-02 to F1-04, F1-08 to F1-11, F1-14
CN5-C only F1-01, F1-05, F1-06, F1-20
CN5-B only F1-31, F1-32, F1-35, F1-36
No. Parameter Name Option Port Setting Range Default
F1-01
<1> For details on the default settings, refer to Control Mode Dependent Parameter Default Values on page 84 .
PG 1 Pulses Per Revolution CN5-C 0 to 60000 ppr Determined by A1-02
<1>
F1-31 PG 2 Pulses Per Revolution CN5-B 0 to 60000 ppr Determined by A1-02
<1>
No. Parameter Name Option Port Setting Range Default
F1-02 Operation Selection at PG Open Circuit (PGo) CN5-B, CN5-C 0 to 4 1
F1-14 PG Open-Circuit Detection Time CN5-B, CN5-C 0.0 to 10.0 s 2.0 s
No. Parameter Name Option Port Setting Range Default
F1-03
<1> For details on the default settings, refer to Control Mode Dependent Parameter Default Values on page 84 .
Operation Selection at Overspeed (oS) CN5-B, CN5-C 0 to 3 1
F1-08 Overspeed Detection Level CN5-B, CN5-C 0 to 120% 115%
F1-09 Overspeed Detection Delay Time CN5-B, CN5-C 0.0 to 2.0 s Determined by A1-02
<1>
MV1000ParameterGuide_E_conditional.book 163 ページ ２０１３年１０月１１日 金曜日 午後８時１８分