YASKAWA CIPR-GA50C series, Technical Manual

Page: 169 / 766

Standards
Compliance
5
5.2 European Standards
YASKAWA SIEPC71061753A GA500 Technical Manual 169
Model Terminal
Recommended
Gauge
mm 2
Applicable Gauge
mm 2
Wire
Stripping
Length
*1
mm
Terminal Screw
Tightening Torque
N
∙
m (in
∙
lb)
Size Shape
4060
R/L1, S/L2, T/L3 25 6 - 35 18 M5
• ≤ 25 mm 2
2.3 - 2.5
(19.8 - 22)
• 35 mm 2 ≤
4.1 - 4.5
(36 - 40)
U/T1, V/T2, W/T3 16 4 - 25 18 M5
2.3 - 2.5
(19.8 - 22)
-, +1, +2 25 6 - 35 18 M5
• ≤ 25 mm 2
2.3 - 2.5
(19.8 - 22)
• 35 mm 2 ≤
4.1 - 4.5
(36 - 40)
B1, B2 10 2.5 - 16 10 M4
1.5 - 1.7
(13.5 - 15)
10 6 - 16 - M6
5.4 - 6.0
(47.8 - 53.1)
*1 Remove insulation from the ends of wires to expose the length of wire shown.
*2 If you turn on the internal EMC filter, the leakage current of the drive will be more than 3.5 mA. Use these closed-loop crimp
terminals or equivalent to connect a protective ground wire that has a minimum cross-sectional area of 10 mm
2 (copper wire).
• 8-4NS from JST Mfg. Co., Ltd.
• R8-4S from NICHIFU Co.,Ltd.
■
Connect a Fuse to the Input Side (Primary Side)
The drive circuit protection must comply with EN 61800-5-1:2007 for protection against a short circuit in the
internal circuitry. Connect semiconductor protection fuses on the input side for branch circuit protection.
Refer to Single-Phase 200 V Class on page 169 , Three-Phase 200 V Class on page 169 , and Three-Phase 400 V
Class on page 170 for more information about recommended fuses.
WARNING! Electrical Shock Hazard. After the drive blows a fuse or trips an RCM/RCD, do not immediately energize the drive
or operate peripheral devices. Wait for the time specified on the warning label at a minimum and make sure that all indicators
are OFF. Then check the wiring and peripheral device ratings to find the cause of the problem. If you do not know the cause of
the problem, contact Yaskawa before you energize the drive or peripheral devices. If you do not fix the problem before you
operate the drive or peripheral devices, it can cause serious injury or death.
Three-Phase 200 V Class
Table 5.2 Factory-Recommended Branch Circuit Protection: Three-Phase 200 V Class
Drive Model
Semiconductor Protection Fuse
Rated Current
Manufacturer: EATON/Bussmann
2001 FWH-25A14F
2002 FWH-25A14F
2004 FWH-25A14F
2006 FWH-25A14F
2010 FWH-70B
2012 FWH-70B
Drive Model
Semiconductor Protection Fuse
Rated Current
Manufacturer: EATON/Bussmann
2021 FWH-90B
2030 FWH-100B
2042 FWH-150B
2056 FWH-200B
2070 FWH-200B
2082 FWH-225A
Single-Phase 200 V Class
Table 5.3 Factory-Recommended Branch Circuit Protection: Single-Phase 200 V Class
Drive Model
Semiconductor Protection Fuse
Rated Current
Manufacturer: EATON/Bussmann
B001 FWH-25A14F
B002 FWH-25A14F
B004 FWH-60B
B006 FWH-80B
Drive Model
Semiconductor Protection Fuse
Rated Current
Manufacturer: EATON/Bussmann
B010 FWH-100B
B012 FWH-125B
B018 FWH-150B