manualshive.com logo in svg

Yardistry 1902316, Installation And Operating Instructions Manual

Share
Download
Yardistry 1902316 Installation And Operating Instructions Manual Download Page 11

 11 

[email protected]

Step 1

Post Mount to Post             2 - 5/16 x 1¼ Hex Bolt (5/16 flat, lock washer and t-nut)

                                                4 - #8x1½ wood screw

                                                4 - # 10x1¼ Pan screw

Step 1

Post Mount to Post             2 - 5/16 x 1¼ Hex Bolt (5/16 flat, lock washer and t-nut)

                                                4 - #8x1½ wood screw

                                                4 - # 10x1¼ Pan screw

A:

  At the bottom of one (902) Pergola Post insert two 5/16” T-Nuts as shown in F2.2.  

B:

  At the bottom of (902) Pergola Post place two Post Mounts tight to the bottom and inside faces as shown in 

F2.1 and F2.2.  Loosely attach with one 5/16 x 1-1/4” 

Hex Bolt (with 5/16” lock washer and 5/16” flat washer) per 

mount so they connect to the T-Nuts. 

Step 2:  Post Assemblies, Part 1  

Hardware

Wood Parts

F2.1

4  x  (902) Pergola Post   

Top

Bottom

F2.2

8 x 5/16” T-Nut
8 x 5/16 x 1-1/4” Hex Bolt 

(with 5/16” lock washer, 5/16” flat washer)

8 x Post Mount

Post 

Mount

5/16” 

T-Nut

(902) 

Pergola Post

Post 

Mount

5/16” Flat 

Washer

5/16” Lock 

Washer

5/16 x 1-1/4” 

Hex Bolt

5/16” 

T-Nut

(902) 

Pergola Post

5/16 x 1-1/4” 

Hex Bolt

5/16” Lock 

Washer

Summary of Contents for 1902316

































Reviews:

No comments

Brands by name

Popular brands

Load more brands