background image

10

Cutting Height Adjustment Lever

This lever, located at each wheel, lets you adjust cutting 
height of the grass. Remember to put all four levers at 
the same height to avoid uneven cut.

Throttle Control

 

The engine is equipped with a constant speed throttle 
for maximum engine and cutting performance.

Recoil Starter

The recoil starter is attached to the handle. Stand 
behind the unit and pull the recoil starter to start engine.

Primer

The primer is used to pump gas into the carburetor. Use 
it to assist in starting a cold engine, but do not use it 
when restarting a warm engine after a short shutdown.

Mulching Plug

The mulching plug is used only for mulching purposes. 
Instead of collecting the grass clippings in a grass 
catcher, some mower models have the option of 
recirculating the clippings back to the lawn. This is 
called mulching.

SECTION 5:  OPERATING YOUR LAWN MOWER

Gas and Oil Fill-Up 

Service the engine with gasoline and oil as 
instructed in the separate engine manual packed 
with your mower. Read instructions carefully.

Before Starting Mower

Attach spark plug wire to spark plug. Make certain 
the metal cap on the end of the spark plug wire is 
fastened securely over the metal tip on the spark 
plug.

Starting Engine

Push the primer three times. Wait two seconds 
between each push. In temperatures below 55° F, 
prime five times. Do not prime to restart a warm 
engine after a short shutdown.

Standing behind the mower, depress the blade 
control handle and hold it against the upper handle.

Grasp starter handle and pull rope out slowly until 
engine reaches start of compression cycle (rope 
will pull slightly harder at this point). Let the rope 
rewind slowly. Pull rope with a rapid, continuous, 
full arm stroke. Keeping a firm grip on the starter 
handle, let the rope rewind slowly.

Stopping Engine 

Release blade control handle to stop the engine 
and the blade.

Disconnect spark plug wire and move away from 
spark plug to prevent accidental starting. 

WARNING: 

Never fill fuel tank indoors, or 

when engine is running or hot. Do not smoke 
when filling up the fuel tank.

WARNING: 

Be sure no one other than the 

operator is standing near the lawn mower while 
starting engine or operating mower. 

WARNING: 

Never run engine indoors or in 

enclosed, poorly ventilated areas. Engine 
exhaust contains carbon monoxide, an 
odorless and deadly gas.

WARNING: 

Keep hands, feet, hair and 

loose clothing away from any moving parts on 
engine and lawn mower.

Summary of Contents for 437



















Reviews: