manualshive.com logo in svg

Yard-Man 106D, Operator'S Manual, Page: 17 / 20

Share
Download
Yard-Man 106D Operator'S Manual Download Page 17

17

Model 106D

Ref. No.

Part No.

Description

1.

647-0070

Control Handle Assembly

731-2623

Bail Cover (Not shown)

6

749-1406A

Upper Handle

7.

710-1205

Rope Guide

8.

710-1174

Carriage Bolt

9.

749-0928A

Lower Handle

10.

720-0279

Wing Nut

11.

720-0284

Hand Knob

12.

714-0104

Hairpin Clip

13.

746-1142

Control Cable 56.75”

15.

726-0240

Cable Tie

16.

17098

Hinge Clip

17.

731-04019

Trail Shield

18.

682-0139

Cutting Deck Assembly: 20”

19.

736-0105

Bell Washer

20.

720-0426

Knob: Height Adjustment

21.

732-0404

Lever: Spring

22.

734-2004A

Wheel Assembly

23.

736-0504

Wave Washer

24.

738-0102

Axle Bolt

25.

731-1426

Hubcap: Radial Spoke, Yellow

26.

738-0507B

Shoulder Bolt

27.

15262B

Pivot Bar

28.

682-3024

Handle Bracket Assembly RH

682-3025

Handle Bracket Assembly LH*

29.

738-0585

Stake Bolt

30.

732-0731

Torsion Spring

31.

14578

Height Adjust. Assembly RH

14579

Height Adjust. Assembly LH*

32.

782-7006

Mounting Bracket

33.

736-0270

Bell Washer

34.

710-0599

Hex Washer Hd. TT Screw

35.

710-0654A

TT Sems Screw

36.

731-1409

Chute Deflector

37.

682-7002

Mulching Plug Assembly

38.

712-0431

Hex Lock  Nut

39.

15261A

Height Adjustment Plate

40.

731-1933

Cover: Front End

41.

748-0376C

Blade Adapter

753-0588

Blade Adapter Kit (for service)

42.

742-0740

20” Mulching Blade

43.

736-0524A

Blade Bell Support

44.

710-1044

Hex Bolt

45.

747-0710

Hinge Pin

46.

736-0451

Saddle Washer

47.

710-0501

Hex Hd. Cap Screw

48.

710-1256

Hi-Low Scr. 1/4-20

49.

712-0324

Hex Lock Nut 1/4-20 Gr. 8

50.

731-2532

Control Cover LH

51.

731-2533

Control Cover RH

52.

782-0156 Lever

53.

731-1172

Torsion Spring

54.

732-1171

Compression Spring

55.

720-0428

Button

56.

716-0209

Retention Spring

57.

715-0168

Pin

         -

737-0476

Bottle of Oil

Ref. No.

Part No.

Description

*  Not shown in Illustration on previous page

NOTE:

 For 

painted parts

, please refer to

the list of color codes below.  Please add
the applicable color code, wherever
needed, to the part number to order a
replacement part.  For instance, if a part
numbered 700-xxxx is painted Yard-Man
Green, the part number to order would be
700-xxxx-0665.

Yard-Man Green: 0665

Yard-Man Yellow: 0674

Powder Black: 0637

Summary of Contents for 106D





















Reviews:

No comments