background image

17

a. The mower does not propel itself with the 

drive control lever engaged.

b. The mower’s drive wheels hesitate with the 

drive control lever engaged. 

To resolve the above problems, rotate the 
adjustment wheel with your fingers: clockwise to 
tighten the cable, and counter-clockwise to loosen 
the cable. See Figure 23 .

Figure 23

Adjusting Handle Height

Your mower is shipped with the handle in the higher 
height position. To lower the handle height, proceed as 
follows.

Remove the starter rope from the rope guide.

Remove the upper handle by removing the hand 
knobs and carriage bolts. Lay the upper handle out 
of the way, being careful not to bend or kink the 
cables.

Remove the hairpin clips from the weld pins on the 
handle brackets. Refer to Figure 4. Press out on the 
legs of the lower handle. Remove lower handle 
from the mower.

Turn the lower handle around so the notch on the 
bottom of the lower handle is facing forward as 
shown in Figure 24. Reassemble, placing the 
bottom holes in the handle over the weld pins in the 
handle mounting bracket.

Figure 24

Reassemble the upper handle to the lower handle.

Place the hairpin clips in the inner holes of the weld 
pins and attach the starter rope as instructed in the 
Assembling Your Lawn Mower section.

Adjusting Cutting Height

IMPORTANT:

 All wheels must be placed in the same 

relative position. For rough or uneven lawns, move the 
height adjustment lever to a higher position. This will 
help stop scalping of the grass.

An adjusting plate and thumb lever at each wheel 
position provides cutting height adjustment. Each 
adjusting plate has nine height positions. Height of cut 
will be changed when the thumb lever is moved from 
one hole to another. 

Simply depress the lever towards the wheel and 
move the lever assembly to desired position. See 
Figure 25. 

Figure 25

Adjusting Carburetor

NOTE: 

A dirty air cleaner may cause an engine to run

rough too. Make sure that the air cleaner is clean and
attached to the carburetor before deciding to adjust the
carburetor. 

To adjust the carburetor, please follow the 
recommendations and instructions found in the engine 
manual. 

WARNING: If any adjustments are made to
the engine (e.g. carburetor) while the
engine is running, keep clear of all moving
parts. Be careful of heated surfaces like the
muffler. 

To tighten 
cable

To loosen
cable

Adjustment
Wheel

Notch

Lower
Handle

Height Adjustment 
Lever

Summary of Contents for 440 Thru E459




























Reviews: