Yanmar i8350 Operation Manual Download Page 23

Page: 23 / 28

Page 2

Electronic Control System:

Operation Manual for SY Series Engines with GEN III Controls

fuses

There is a fuse on the back of both the lower station and upper Station Ignition Switch Panels. It is a 5 amp fuse,

designation AGC 5A. There are five circuit breakers inside the i8350/55 Engine Interface. See image on page

14 for details.

Appendix D

Appendix E

Diagnostic trouble Code Descriptions

NOTE: On the digital display the DTC “Y” code will be shown along with additional information for that code.

This information will further define the fault. Please make note of all the information details with the Y code

before notifying your Yanmar service technician.

Y-value

Text Message

Y0011

OvERREvING

Y0012

SPEED SENSOR 1

Y0013

SPEED SENSOR 2

Y0014

WATER TEMPERATURE SENSOR

Y0015

CHARGE AIR TEMPERATURE SENSOR

Y0016

CHARGE AIR PRESSURE SENSOR

Y0018

OIL PRESSURE SENSOR

Y0023

FAULT IN i8350 MODULE

Y0025

THROTTLE FAULT

Y0027

EMERGENCY STOP OvERRIDE

Y0028

OIL PRESSURE SHUT OFF

Y0031

OIL PRESSURE PROTECTION

Y0033

BATTERY vOLTAGE

Y0037

EMERGENCY STOP - i8350 MODULE

Y0043

CAN - CIRCUIT DEFECT

Y0046

OvERREvING, EXHAUST BRAKING

Y0048

CAN MESSAGE FROM i8350 (DLN1)

Y0049

WRONG CAN vERSION

Y0051

UNIT INjECTOR CYLINDER 1

Y0052

UNIT INjECTOR CYLINDER 2

Y0053

UNIT INjECTOR CYLINDER 3

Y0054

UNIT INjECTOR CYLINDER 4

Y0055

UNIT INjECTOR CYLINDER 5

Y0056

UNIT INjECTOR CYLINDER 6

continued on next page

Summary of Contents for i8350





























Search results

Summary of Contents for i8350

Reviews:

Related manuals for i8350

Brands by name

Popular brands

Yanmar i8350, Operation Manual

Search results

Summary of Contents for i8350

Reviews:

Related manuals for i8350

Brands by name

Popular brands