background image

 

Important manual information

 

EMU25100

 

To the owner

 

Thank you for choosing a Yamaha outboard
motor. This Owner’s Manual contains infor-
mation needed for proper operation, mainte-
nance and care. A thorough understanding
of these simple instructions will help you ob-
tain maximum enjoyment from your new
Yamaha. If you have any question about the
operation or maintenance of your outboard
motor, please consult a Yamaha dealer.
In this Owner’s Manual particularly important
information is distinguished in the following
ways.

 The Safety Alert Symbol means AT-

TENTION! BECOME ALERT! YOUR SAFE-
TY IS INVOLVED!

WARNING

 

EWM00780 

 

Failure to follow WARNING instructions
could result in severe injury or death to
the machine operator, a bystander, or a
person inspecting or repairing the out-

 

board motor.

CAUTION:

 

ECM00700 

 

A CAUTION indicates special precautions
that must be taken to avoid damage to the

 

outboard motor.

NOTE:

 

A NOTE provides key information to make

 

procedures easier or clearer.

Yamaha continually seeks advancements in
product design and quality. Therefore, while
this manual contains the most current prod-
uct information available at the time of print-
ing, there may be minor discrepancies
between your machine and this manual. If
there is any question concerning this manu-

al, please consult your Yamaha dealer.

NOTE:

 

The Z300AETO, LZ300AETO and the stan-
dard accessories are used as a base for the
explanations and illustrations in this manual.
Therefore some items may not apply to ev-

 

ery model.

 

EMU25120

 

Z300A, LZ300A

OWNER’S MANUAL

©2003 by Yamaha Motor Co., Ltd.

1st Edition, August 2003

All rights reserved.

Any reprinting or unauthorized use

without the written permission of

Yamaha Motor Co., Ltd.
is expressly prohibited.

Printed in Japan

Summary of Contents for Z300A 2003









































































Reviews: