Yamaha YZ85W1 Service Manual Download

Page: 145 / 255

CHAS

4-73

EAS00706

REMOVING THE DRIVE CHAIN

1. Stand the vehicle on a level surface.

WARNING

Securely support the vehicle so that there
is no danger of it falling over.

NOTE:

Place the vehicle on a suitable stand so that
the rear wheel is elevated.

2. Remove:

• master link clip
• master link
• master link plate
• drive chain

EAS00707

CHECKING THE SWINGARM

1. Check:

• swingarm

Bends / cracks / damage

→

Replace.

2. Check:

• pivot shaft

Roll the pivot shaft on a flat surface.

Bends

→

Replace.

WARNING

Do not attempt to straighten a bent pivot
shaft.

3. Wash:

• pivot shaft
• collar
• bearings

Recommended cleaning solvent

Kerosene

SWINGARM AND DRIVE CHAIN

Summary of Contents for YZ85W1
































































































































































































































































Search results

Summary of Contents for YZ85W1

Reviews:

Related manuals for YZ85W1

Brands by name

Popular brands

Yamaha YZ85W1, Service Manual

Search results

Summary of Contents for YZ85W1

Reviews:

Related manuals for YZ85W1

Brands by name

Popular brands