Yamaha YP125R Service Manual Download Page 486

Page: 486 / 498

ELECTRICAL COMPONENTS

8-89

c. Set the main switch to “ON”.
d. Measure the intake air pressure sensor out-

put voltage.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

EAS28420

CHECKING THE INTAKE AIR
TEMPERATURE SENSOR

1. Remove:

• Intake air temperature sensor

(from the air filter case)

WARNING

EWA14110

• Handle the intake air temperature sensor

with special care.

• Never subject the intake air temperature

sensor to strong shocks. If the intake air
temperature sensor is dropped, replace it.

2. Check:

• Intake air temperature sensor resistance

Out of specification

→

Replace.

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Connect the pocket tester (

Ω

1k) to the in-

take air temperature sensor terminal as
shown.

b. Immerse the intake air temperature sensor

“1” in a container filled with water “2”.

TIP

Make sure that the intake air temperature sensor
terminals do not get wet.

c. Place a thermometer “3” in the water.

d. Heat the water or let it cool down to the spec-

ified temperature.

e. Measure the intake air temperature sensor

resistance.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

EAS37P1083

CHECKING THE AIR TEMPERATURE
SENSOR

1. Remove:

• Air temperature sensor

WARNING

EWA37P1017

• Handle the air temperature sensor with

special care.

• Never subject the air temperature sensor to

strong shocks. If the air temperature sen-
sor is dropped, replace it.

2. Check:

• Air temperature sensor resistance

Out of specification

→

Replace.

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Connect the pocket tester (

Ω

1k) to the air

temperature sensor terminal as shown.

Test harness

90890-03204

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

• Positive tester probe

→

pink/white “1”

• Negative tester probe

→

gray/black “2”

Intake air temperature sensor re-
sistance

2.21–2.69 k

Ω

at 20 °C (68 °F)

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

Air temperature sensor resis-
tance

4.19–4.63 k

Ω

at 50 °C (122 °F)

Summary of Contents for YP125R



















































































































































































































































































































































































































































































































Search results

Summary of Contents for YP125R

Reviews:

Related manuals for YP125R

Brands by name

Popular brands

Yamaha YP125R, Service Manual

Search results

Summary of Contents for YP125R

Reviews:

Related manuals for YP125R

Brands by name

Popular brands