manualshive.com logo in svg

Yamaha YP125R, Service Manual

The Yamaha YP125R Owner's Manual is a comprehensive guide that provides detailed instructions and information about the operation and maintenance of the Yamaha YP125R. With our user-friendly website, users can easily download this manual for free, ensuring a worry-free ownership experience. Visit manualshive.com to access your free manual today.

Share
Download
background image

8

ELECTRICAL SYSTEM

IGNITION SYSTEM

......................................................................................... 8-1

CIRCUIT DIAGRAM .................................................................................. 8-1
TROUBLESHOOTING .............................................................................. 8-3

ELECTRIC STARTING SYSTEM

.................................................................... 8-5

CIRCUIT DIAGRAM .................................................................................. 8-5
STARTING CIRCUIT CUT-OFF SYSTEM OPERATION .......................... 8-7
TROUBLESHOOTING .............................................................................. 8-9

CHARGING SYSTEM

.................................................................................... 8-11

CIRCUIT DIAGRAM ................................................................................ 8-11
TROUBLESHOOTING ............................................................................ 8-13

LIGHTING SYSTEM

...................................................................................... 8-15

CIRCUIT DIAGRAM ................................................................................ 8-15
TROUBLESHOOTING ............................................................................ 8-17

SIGNALING SYSTEM

................................................................................... 8-19

CIRCUIT DIAGRAM ................................................................................ 8-19
TROUBLESHOOTING ............................................................................ 8-21

COOLING SYSTEM

....................................................................................... 8-27

CIRCUIT DIAGRAM ................................................................................ 8-27
TROUBLESHOOTING ............................................................................ 8-29

FUEL INJECTION SYSTEM

.......................................................................... 8-31

CIRCUIT DIAGRAM ................................................................................ 8-31
ECU SELF-DIAGNOSTIC FUNCTION.................................................... 8-33
TROUBLESHOOTING METHOD............................................................ 8-34
DIAGNOSTIC MODE .............................................................................. 8-34
TROUBLESHOOTING DETAILS ............................................................ 8-36
DIAGNOSTIC CODE TABLE .................................................................. 8-54

FUEL PUMP SYSTEM

................................................................................... 8-57

CIRCUIT DIAGRAM ................................................................................ 8-57
TROUBLESHOOTING ............................................................................ 8-59

IMMOBILIZER SYSTEM

................................................................................ 8-61

CIRCUIT DIAGRAM ................................................................................ 8-61
GENERAL INFORMATION ..................................................................... 8-63
PART REPLACEMENT AND KEY CODE REGISTRATION 

REQUIREMENTS................................................................................... 8-63

TROUBLESHOOTING ............................................................................ 8-67
SELF-DIAGNOSIS FAULT CODE INDICATION ..................................... 8-67

Summary of Contents for YP125R



















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for YP125R

VOLTRIUM Rogue 1200 Gen 1 Owner'S Manual preview
Rogue 1200 Gen 1
Brand: VOLTRIUM Pages: 17
Blaupunkt e mobility Clara Owner'S Manual preview
e mobility Clara
Brand: Blaupunkt Pages: 154
Abilize MS01073 Instruction Booklet preview
MS01073
Brand: Abilize Pages: 14
Kangaroo Golf Z 2020 Series Quick Start Manual preview
Z 2020 Series
Brand: Kangaroo Golf Pages: 7
Hudora 14124 Instructions On Assembly And Use preview
14124
Brand: Hudora Pages: 28
EzyWheel EzyOne 2020 User Manual preview
EzyOne 2020
Brand: EzyWheel Pages: 26
VESPA LX 125ie 3Valvole Manual preview
LX 125ie 3Valvole
Brand: VESPA Pages: 94
Iveco DAILY 4x4 Instructions Manual preview
DAILY 4x4
Brand: Iveco Pages: 110
Trevi VELOCIPTOR ES 85W User Manual preview
VELOCIPTOR ES 85W
Brand: Trevi Pages: 16
RAEV BULLET PRO User Manual preview
BULLET PRO
Brand: RAEV Pages: 16
EasyTravel ET1L User Manual preview
ET1L
Brand: EasyTravel Pages: 24
Jetson Glyro User Manual preview
Glyro
Brand: Jetson Pages: 16
Xiaomi Mi Smart Air Purifier 4 Lite User Manual preview
Mi Smart Air Purifier 4 Lite
Brand: Xiaomi Pages: 19
UltraLite AutoGo 550 Owner'S Manual preview
AutoGo 550
Brand: UltraLite Pages: 59
Razor Junior T3 Owner'S Manual preview
Junior T3
Brand: Razor Pages: 8
Pride Mobility Elite Traveller Series INFINFB2039 Troubleshooting Instructions preview
Elite Traveller Series INFINFB2039
Brand: Pride Mobility Pages: 2
Airwheel s8 User Manual preview
s8
Brand: Airwheel Pages: 20
Denver SEL-80125F User Manual preview
SEL-80125F
Brand: Denver Pages: 23

Brands by name

Popular brands

Load more brands