Yamaha YP125R Service Manual Download

Page: 392 / 498

THROTTLE BODY

7-9

EAS37P1074

REMOVING THE FUEL HOSE

1. Extract the fuel in the fuel tank through the

fuel tank filler hole with a pump.

2. Remove:

• Fuel hose connector cover “1”

3. Disconnect:

• Fuel hose “2”

NOTICE

ECA37P1025

• Be sure to disconnect the fuel hose by

hand. Do not forcefully disconnect the
hose with tools.

• Although the fuel has been removed from

the fuel tank, be careful when removing the
fuel hose, since there may be fuel remain-
ing in it.

• Do not disconnect the fuel hose from the

fuel hose connector. Disconnect the con-
nector from the fuel pump.

TIP

Before removing the hose, place a few rags in
the area under where it will be removed.

EAS26980

CHECKING THE FUEL INJECTOR

1. Check:

• Fuel injector

Damage

→

Replace.

EAS26990

CHECKING THE THROTTLE BODY

1. Check:

• Throttle body

Cracks/damage

→

Replace the throttle body.

2. Check:

• Fuel passages

Obstructions

→

Clean.

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Wash the throttle body in a petroleum-based

solvent.
Do not use any caustic carburetor cleaning
solution.

b. Blow out all of the passages with compressed

air.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

3. Check: (YP250R only)

• Piston valve

Damage/scratches/wear

→

Replace.

• Piston valve diaphragm

Cracks/tears

→

Replace.

4. Check: (YP250R only)

• Vacuum chamber cover
• Piston valve spring

Cracks/damage

→

Replace.

5. Check: (YP250R only)

• Piston valve movement

Insert the piston valve into the throttle body
and move it up and down.
Tightness

→

Replace the piston valve.

EAS37P1116

INSTALLING THE INTAKE MANIFOLD
(YP125R)

1. Install:

• Intake manifold joint “1”
• Intake manifold “2”

TIP

Make sure that the projection “a” on the intake
manifold joint is facing down.

EAS37P1073

INSTALLING THE INTAKE MANIFOLD
(YP250R)

1. Install:

• Intake manifold joint “1”

Summary of Contents for YP125R



















































































































































































































































































































































































































































































































Search results

Summary of Contents for YP125R

Reviews:

Related manuals for YP125R

Brands by name

Popular brands

Yamaha YP125R, Service Manual

Search results

Summary of Contents for YP125R

Reviews:

Related manuals for YP125R

Brands by name

Popular brands