Yamaha YP125R Service Manual Download

Page: 199 / 498

FRONT BRAKE

4-24

5. Check:

• Brake lever operation

Soft or spongy feeling

→

Bleed the brake sys-

tem.
Refer to “BLEEDING THE HYDRAULIC
BRAKE SYSTEM” on page 3-36.

EAS22290

REMOVING THE FRONT BRAKE CALIPER

TIP

Before removing the brake caliper, drain the
brake fluid from the entire brake system.

1. Remove:

• Brake hose union bolt “1”
• Copper washers “2”
• Front brake hose “3”

TIP

Put the end of the brake hose into a container
and pump out the brake fluid carefully.

EAS22320

DISASSEMBLING THE FRONT BRAKE
CALIPER

1. Remove:

• Brake caliper pistons “1”
• Brake caliper piston dust seals “2”
• Brake caliper piston seals “3”

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Blow compressed air into the brake hose joint

opening “a” to force out the pistons from the
brake caliper.

WARNING

EWA13550

• Cover the brake caliper piston with a rag.

Be careful not to get injured when the pis-
ton is expelled from the brake caliper.

• Never try to pry out the brake caliper pis-

ton.

b. Remove the brake caliper piston dust seals

and brake caliper piston seals.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

EAS22380

CHECKING THE FRONT BRAKE CALIPER

1. Check:

• Brake caliper pistons “1”

Rust/scratches/wear

→

Replace the brake

caliper pistons.

• Brake caliper cylinders “2”

Scratches/wear

→

Replace the brake caliper

assembly.

• Brake caliper body “3”

Cracks/damage

→

Replace the brake caliper

assembly.

• Brake fluid delivery passages

(brake caliper body)
Obstruction

→

Blow out with compressed air.

WARNING

EWA37P1010

Whenever a brake caliper is disassembled,
replace the brake caliper piston dust seals
and brake caliper piston seals.

Recommended brake component replace-

ment schedule

Brake pads

If necessary

Piston seals

Every two years

Piston dust seals

Every two years

Brake hose

Every four years

Brake fluid

Every two years and
whenever the brake
is disassembled

Summary of Contents for YP125R



















































































































































































































































































































































































































































































































Search results

Summary of Contents for YP125R

Reviews:

Related manuals for YP125R

Brands by name

Popular brands

Yamaha YP125R, Service Manual

Search results

Summary of Contents for YP125R

Reviews:

Related manuals for YP125R

Brands by name

Popular brands