Yamaha YP125R Service Manual Download Page 163

Page: 163 / 498

CHASSIS

3-36

EAS21260

CHECKING THE REAR BRAKE PADS
(YP250R)

The following procedure applies to all of the
brake pads.
1. Operate the brake.
2. Check:

• Rear brake pad

Wear indicator groove “a” has almost disap-
peared

→

Replace the brake pads as a set.

Refer to “REAR BRAKE” on page 4-29.

EAS21270

CHECKING THE FRONT BRAKE HOSE

1. Check:

• Brake hose “1”

Cracks/damage/wear

→

Replace.

2. Hold the vehicle upright and apply the front

brake several times.

3. Check:

• Brake hose

Brake fluid leakage

→

Replace the damaged

hose.
Refer to “FRONT BRAKE” on page 4-17.

EAS21290

CHECKING THE REAR BRAKE HOSE

1. Check:

• Brake hose “1”

Cracks/damage/wear

→

Replace.

2. Check:

• Brake hose holder “2”

Loose connection

→

Connect.

3. Hold the vehicle upright and apply the rear

brake several times.

4. Check:

• Brake hose

Brake fluid leakage

→

Replace the damaged

hose.
Refer to “REAR BRAKE” on page 4-29.

EAS21350

BLEEDING THE HYDRAULIC BRAKE
SYSTEM

WARNING

EWA37P1005

Bleed the hydraulic brake system whenever:
• The system is disassembled.
• A brake hose is loosened, disconnected or

replaced.

• The brake fluid level is very low.
• The brake operation is faulty.

TIP

• Be careful not to spill any brake fluid or allow

the brake master cylinder reservoir to overflow.

A. YP125R
B. YP250R

Summary of Contents for YP125R



















































































































































































































































































































































































































































































































Search results

Summary of Contents for YP125R

Reviews:

Related manuals for YP125R

Brands by name

Popular brands

Yamaha YP125R, Service Manual

Search results

Summary of Contents for YP125R

Reviews:

Related manuals for YP125R

Brands by name

Popular brands