Yamaha YFM700RF Owner'S Manual Download | Manualshive

Page: 52 / 160

background image

4-24

4

Rebound damping force

Turn the rebound damping force adjusting screw
in direction (a) to increase the rebound damping
force and thereby harden the damping, and in di-
rection (b) to decrease the rebound damping force
and thereby soften the damping.

Compression damping force

Compression damping force (for fast compres-
sion damping)
To increase the compression damping force and
thereby harden the compression damping, turn
the compression damping force adjusting bolt in
direction (a). To decrease the compression damp-
ing force and thereby soften the compression
damping, turn the adjusting bolt in direction (b).

Tightening torque:

Locknut:

42 Nm (4.2 m·kgf, 30 ft·lbf)

1. Rebound damping force adjusting screw

1

(b)

(a)

Rebound damping setting:

Minimum (soft):

30 click(s) in direction (b)*

Standard:

18 click(s) in direction (b)*

Maximum (hard):

1 click(s) in direction (b)*

* With the adjusting screw fully turned in di-

rection (a)

U2LS60E0.book Page 24 Wednesday, June 18, 2014 11:12 AM

«
...
50
51
52
53
54
...
»

Summary of Contents for YFM700RF

































































































































































Reviews:

No comments

Related manuals for YFM700RF

Brand: Bad Boy Pages: 132

Standard Pedal-Kart

Brand: DINO CARS Pages: 4

Brand: B&P Manufacturing Pages: 6

LEXION 770 2016

Brand: Claas Pages: 48

TRX90 Sportrax 90

Brand: Honda Pages: 208

Brand: Foldy Pages: 44

Brand: Erde Pages: 4

Brand: Wittke Pages: 104

Brand: Leggero Pages: 98

Minor VM Hydrostatic

Brand: Scarab Pages: 32

Brand: Palms Pages: 19

Brand: Jayco Pages: 124

Brand: Jeep Pages: 16

Brand: SANMEN COUNTY YONGFU MACHINE Pages: 73

Brand: Kellfri Pages: 12

GRIZZLY 350 YFM35GZ

Brand: Yamaha Pages: 138

Brand: Access Motor Pages: 59

2009 LT-A750XK9

Brand: Suzuki Pages: 711

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands