Yamaha YFM450FAZ Owner'S Manual Download

Page: 155 / 166

10-1

EBU25960

SPECIFICATIONS

Dimensions:

Overall length:

1991 mm (78.4 in)

Overall width:

1093 mm (43.0 in)

Overall height:

1120 mm (44.1 in)

Seat height:

850 mm (33.5 in)

Wheelbase:

1233 mm (48.5 in)

Ground clearance:

245 mm (9.6 in)

Minimum turning radius:

3000 mm (118 in)

Weight:

With oil and fuel:

YFM450FAZ 289.0 kg (637 lb)
YFM45FGHZ 285.0 kg (628 lb)
YFM45FGZ 285.0 kg (628 lb)

Noise and vibration level:

Noise level (77/311/EEC):

YFM45FGHZ 78.3 dB(A)
YFM45FGZ 78.3 dB(A)

Vibration on seat (EN1032, ISO5008):

YFM45FGHZ Will not exceed 0.5 m/s²
YFM45FGZ Will not exceed 0.5 m/s²

Vibration on handlebar (EN1032, ISO5008):

YFM45FGHZ Will not exceed 2.5 m/s²
YFM45FGZ Will not exceed 2.5 m/s²

Engine:

Engine type:

Liquid cooled 4-stroke, SOHC

Cylinder arrangement:

Forward-inclined single cylinder

Displacement:

421 cm³

Bore

stroke:

84.5

75.0 mm (3.33

2.95 in)

Compression ratio:

10.00 :1

Starting system:

Electric and recoil starter

Lubrication system:

Wet sump

Engine oil:

Recommended brand:

YAMALUBE

U37S61E0.book Page 1 Tuesday, June 2, 2009 10:33 AM

Summary of Contents for YFM450FAZ







































































































































































Search results

Summary of Contents for YFM450FAZ

Reviews:

Related manuals for YFM450FAZ

Brands by name

Popular brands

Yamaha YFM450FAZ, Owner'S Manual

Search results

Summary of Contents for YFM450FAZ

Reviews:

Related manuals for YFM450FAZ

Brands by name

Popular brands