manualshive.com logo in svg

Yamaha YFM35RX, Owner'S Manual

The Yamaha YFM35RX Owner's Manual is a comprehensive guide for users of this powerful off-road vehicle. This indispensable manual provides detailed instructions, important safety information, and maintenance tips to ensure optimal performance. Download your free manual from our website and unleash the full potential of your Yamaha YFM35RX.

Share
Download
background image

5-4

5

Brake fluid leakage

Check to see if any brake fluid is leaking out of the
pipe joints or brake fluid reservoirs. Apply the
brakes firmly for one minute. If there is any leak-
age, have a Yamaha dealer check the brake sys-
tem.

Brake operation

Test the brakes at slow speed after starting out to
make sure they are working properly. If the brakes
do not provide proper braking performance, check
the brake pads for wear. (See page 8-22.)

WARNING

EWB00580

Always check the brakes at the start of every
ride. Do not ride the ATV if you find any prob-
lem with the brakes or you could lose braking
ability, which could lead to an accident. If a
problem cannot be corrected by the adjust-
ment procedures provided in this manual, have
a Yamaha dealer check for the cause.

EBU19761

Throttle lever 

Check the operation of the throttle lever. It must
open smoothly and spring back to the idle position
when released. Have a Yamaha dealer correct if
necessary.

EBU19770

Drive chain 

Check the condition of the drive chain and check
the drive chain slack. Lubricate and adjust the
drive chain as necessary. (See page 8-29.)

EBU19791

Tires 

WARNING

EWB00601

Use of improper tires on this ATV, or operation
of this ATV with improper or uneven tire pres-
sure, may cause loss of control, increasing
your risk of accident.
Pay attention to the following.

●

The tires listed below have been approved
by Yamaha Motor Co., Ltd. for this model.
Other tire combinations are not recommend-
ed.

U5YT64E0.book  Page 4  Monday, April 9, 2007  1:03 PM

Summary of Contents for YFM35RX







































































































































Reviews:

No comments

Related manuals for YFM35RX

Brands by name

Popular brands

Load more brands