Yamaha YFM35RX Owner'S Manual Download

Page: 107 / 134

8-29

7. To increase the clutch lever free play, turn the

adjusting nut at the crankcase in direction (a),
and to decrease it, turn the nut in direction (b).

8. Tighten the locknut at the crankcase and the

clutch lever.

NOTE:

If the specified free play cannot be obtained as de-
scribed above or if the clutch does not operate cor-
rectly, have a Yamaha dealer check the internal
clutch mechanism.

EBU24842

Drive chain slack

The drive chain slack should be checked before
each ride and adjusted if necessary.

To check the drive chain slack

1. Place the ATV on a level surface.

NOTE:

When checking and adjusting the drive chain
slack, there should be no weight on the ATV and
all tires must be touching the ground.

2. Move the ATV back and forth to locate the

tightest portion of the drive chain, and then
measure the drive chain slack as shown.

1. Locknut
2. Clutch lever free play adjusting nut (crankcase)

Drive chain slack:

25.0–35.0 mm (0.98–1.38 in)

U5YT64E0.book Page 29 Monday, April 9, 2007 1:03 PM

Summary of Contents for YFM35RX







































































































































Search results

Summary of Contents for YFM35RX

Reviews:

Related manuals for YFM35RX

Brands by name

Popular brands

Yamaha YFM35RX, Owner'S Manual

Search results

Summary of Contents for YFM35RX

Reviews:

Related manuals for YFM35RX

Brands by name

Popular brands