Yamaha YFM35FGIY Owner'S Manual Download | Manualshive

Page: 37 / 166

background image

4-18

4

RES

This indicates reserve. With the fuel cock lever in
this position, the fuel reserve is made available.
Turn the fuel cock lever to this position if you run
out of fuel while riding. When this occurs, refuel as
soon as possible and be sure to turn the fuel cock
lever back to “ON”!

EBU18850

Starter (choke) “

”

Starting a cold engine requires a richer air-fuel mix-
ture, which is supplied by the starter (choke).
Move the starter (choke) in direction (a) to turn on
the starter (choke).

Move the starter (choke) in direction (b) to turn off
the starter (choke).
See the “Starting a cold engine” section on page
6-1 for proper operation.

EBU18880

Seat

To remove the seat

Pull the seat lock lever upward and pull up the seat
at the rear.

1. Arrow mark pointing to “RES”

1. Starter (choke) “

”

U4S212E0.book Page 18 Thursday, April 17, 2008 9:17 AM

«
...
35
36
37
38
39
...
»

Summary of Contents for YFM35FGIY







































































































































































Reviews:

No comments

Related manuals for YFM35FGIY

Brand: Eagle Pages: 170

Brand: Massimo Pages: 174

Brand: Can-Am Pages: 144

Brand: X-TREME Pages: 11

Brand: NorthStar Pages: 24

Brand: Eagle Pages: 12

MINI BAJA DUNE65

Brand: Baja motorsports Pages: 8

2013 RANGER RZR 570

Brand: Polaris Pages: 152

Brand: Taylor-Dunn Pages: 216

Brand: Stinger Pages: 12

Brand: Elliott Pages: 376

Brand: DSRaider Pages: 23

Brand: CHICAGO Pages: 23

Brand: HAUL MASTER Pages: 24

Brand: MANCO Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands