Yamaha YFM35FGIY Owner'S Manual Download Page 118 | Manualshive

Page: 118 / 166

background image

8-28

8

NOTICE

ECB00480

The carburetor has been set and extensively
tested at the Yamaha factory. Changing these
settings without sufficient technical knowl-
edge may result in poor performance of or
damage to the engine.

EBU24000

Adjusting the engine idling speed

The engine idling speed must be checked and, if
necessary, adjusted as follows at the intervals
specified in the periodic maintenance and lubrica-
tion chart.

TIP

A diagnostic tachometer is needed to make this
adjustment.

1. Start the engine and warm it up.

TIP

The engine is warm when it quickly responds to the
throttle.

2. Attach the tachometer to the spark plug lead.
3. Check the engine idling speed and, if neces-

sary, adjust it to specification by turning the
throttle stop screw at the carburetor. To in-

crease the engine idling speed, turn the throt-
tle stop screw in direction (a), and to decrease
it, turn the screw in direction (b).

TIP

If the specified idling speed cannot be obtained as
described above, have a Yamaha dealer make the
adjustment.

1. Throttle stop screw

Engine idling speed:

1450–1550 r/min

U4S212E0.book Page 28 Thursday, April 17, 2008 9:17 AM

«
...
116
117
118
119
120
...
»

Summary of Contents for YFM35FGIY







































































































































































Reviews:

No comments

Related manuals for YFM35FGIY

Brand: Woodland Mills Pages: 68

Brand: Yerf-Dog Pages: 59

Brand: Polaris Pages: 690

Brand: TSE Pages: 129

BOX LINER TU 70

Brand: Krone Pages: 92

Brand: DAELIM Pages: 163

Brand: allen Pages: 62

Brand: Labrie Pages: 62

Brand: Arctic Cat Pages: 64

2012 90 Utility

Brand: Arctic Cat Pages: 83

Brand: Yamaha Pages: 140

Brand: Zap Pages: 27

2015 WILDCAT SPORT

Brand: Arctic Cat Pages: 68

Brand: Arctic Cat Pages: 84

Brand: Arctic Cat Pages: 177

Brand: Arctic Cat Pages: 190

DVX 90/90 UTILITY

Brand: Arctic Cat Pages: 86

2010 700 Diesel SD

Brand: Arctic Cat Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands