manualshive.com logo in svg

Yamaha XVS950A Midnight Star, Owner'S Manual

Share
Download
Yamaha XVS950A Midnight Star Owner'S Manual Download Page 68

PERIODIC MAINTENANCE AND ADJUSTMENT

6-27

6

TIP

To access the fuel injection system
fuse, remove the starter relay cover by
pulling it upward.

If a fuse is blown, replace it as follows.

1. Turn the key to “OFF” and turn off

the electrical circuit in question.

2. Remove the blown fuse, and then

install a new fuse of the specified
amperage. 

WARNING! Do not

use a fuse of a higher amperage
rating than recommended to
avoid causing extensive dam-
age to the electrical system and
possibly a fire.

 [EWA15131]

3. Turn the key to “ON” and turn on

the electrical circuit in question to
check if the device operates.

4. If the fuse immediately blows

again, have a Yamaha dealer
check the electrical system.

1. Ignition fuse
2. Signaling system fuse

3. Parking lighting fuse

4. Backup fuse (for clock and immobilizer sys-

tem)

5. Headlight fuse

6. Spare fuse

1

2
3
4
5

6

1. Starter relay cover
2. Fuel injection system spare fuse

3. Fuel injection system fuse

3

2

1

Specified fuses:

Main fuse:

40.0 A

Headlight fuse:

20.0 A

Signaling system fuse:

10.0 A

Ignition fuse:

15.0 A

Parking lighting fuse:

10.0 A

Fuel injection system fuse:

10.0 A

Backup fuse:

10.0 A

U26PE3E0.book  Page 27  Tuesday, June 7, 2011  5:19 PM

Summary of Contents for XVS950A Midnight Star

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands