Yamaha XVS65A Owner'S Manual Download

Page: 73 / 98

PERIODIC MAINTENANCE AND ADJUSTMENT

7-35

6. Tighten the front wheel axle pinch

bolt to the specified torque.

7. While applying the front brake,

push down hard on the handlebars
several times to check if the front
fork compresses and rebounds
smoothly.

8. Connect the speedometer cable.

EAU25080

Rear wheel

EAU25142

To remove the rear wheel

WARNING

EWA10821

To avoid injury, securely support the
vehicle so there is no danger of it
falling over.

1. Loosen the axle nut.

2. Disconnect the brake torque rod

from the brake shoe plate by re-
moving the bolt and nut.

3. Loosen the brake torque rod nut at

the swingarm.

4. Remove the brake pedal free play

adjusting nut, and then disconnect
the brake rod from the brake cam-
shaft lever.

5. Remove panel A. (See page 7-9.)
6. Remove the bolts that secure the

final gear case to the swingarm.

Tightening torque:

Wheel axle:

59 Nm (5.9 m·kgf, 43 ft·lbf)

Tightening torque:

Front wheel axle pinch bolt:

20 Nm (2.0 m·kgf, 14 ft·lbf)

1. Axle nut

1. Brake pedal free play adjusting nut
2. Brake camshaft lever

3. Bolt and nut (shoe plate)

4. Brake torque rod
5. Bolt and nut (swingarm)

6. Brake rod

U1BF11E0.book Page 35 Tuesday, April 13, 2010 9:28 AM

Summary of Contents for XVS65A



































































































Search results

Summary of Contents for XVS65A

Reviews:

Related manuals for XVS65A

Brands by name

Popular brands

Yamaha XVS65A, Owner'S Manual

Search results

Summary of Contents for XVS65A

Reviews:

Related manuals for XVS65A

Brands by name

Popular brands