Yamaha XMAX 2022 Owner'S Manual Download Page 77 | Manualshive

Page: 77 / 122

background image

Perio

d

ic maintenance an

d

a

d

justment

8-15

8

a

dd

e

d

to the coolant, have a

Yamaha

d

ealer check the anti-

freeze content of the coolant as
soon as possi

b

le, otherwise the

effectiveness of the coolant will

b

e re

d

uce

d

.

[ECA10473]

6. Install the coolant reservoir cover.
7. Place the left floorboard mat in the

original position and push it down-
ward to secure it.

EAU33032

Chan

g

in

g

the coolant

The coolant must be changed at the in-
tervals specified in the periodic main-
tenance and lubrication chart. Have a
Yamaha dealer change the coolant.

WARNING! Never attempt to remove
the ra

d

iator cap when the en

g

ine is

hot.

[EWA10382]

EAU78574

Air filter an

d

V-

b

elt case air fil-

ter elements

The air filter element and the sub air fil-
ter element should be replaced, and
the pre air filter element and the V-belt
case air filter element should be
cleaned at the intervals specified in the
periodic maintenance and lubrication
chart. Service the air filter elements
more frequently if you are riding in un-
usually wet or dusty areas. The air filter
check hose must be frequently
checked and cleaned if necessary.

Cleanin

g

the air filter check hose

1. Coolant reservoir cap

Coolant reservoir capacity (up to
the maximum level mark):

0.18 L (0.19 US qt, 0.16 Imp.qt)

1

1. Air filter check hose

1

UB5X10E0.book Page 15 Thursday, May 27, 2021 8:55 AM

«
...
75
76
77
78
79
...
»

Summary of Contents for XMAX 2022



























































































































Reviews:

No comments

Related manuals for XMAX 2022

Brand: Öhlins Pages: 8

prodrive SUR 3A00

Brand: Öhlins Pages: 4

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 8

Brand: Öhlins Pages: 4

TroyLee Designs

Brand: A3 HELMET Pages: 244

Brand: Can-Am Pages: 196

Brand: Yoshimura Pages: 4

Brand: Honda Pages: 140

MOTO NOSTRA MN4602

Brand: SC Pages: 8

Evoline 3 Series

Brand: Shark Pages: 31

Brand: Shark Pages: 36

Brand: JETPRIME Pages: 4

VIKING 2450 Series

Brand: Lincoln Electric Pages: 48

Brand: IBEX Pages: 3

Brand: Engelbert Strauss Pages: 32

Brand: Benelli Pages: 243

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands