Yamaha XMAX 2022 Owner'S Manual Download Page 76

Page: 76 / 122

Perio

ic maintenance an

justment

8-14

EAU20071

Coolant

The coolant level should be checked
before each ride. In addition, the cool-
ant must be changed at the intervals
specified in the periodic maintenance
and lubrication chart.

EAU78580

To check the coolant level

1. Place the vehicle on the center-

stand.

TIP



The coolant level must be
checked on a cold engine since
the level varies with engine tem-
perature.



Make sure that the vehicle is posi-
tioned straight up when checking
the coolant level. A slight tilt to the
side can result in a false reading.

2. Check the coolant level through

the check window.

TIP

The coolant should be between the
minimum and maximum level marks.

3. If the coolant is at or below the

minimum level mark, remove the
left floorboard mat by pulling it up.

4. Remove the coolant reservoir cov-

er.

5. Remove the coolant reservoir cap,

add coolant to the maximum level
mark, and then install the reservoir
cap.

WARNING! Remove only

the coolant reservoir cap. Never
attempt to remove the ra

iator

cap when the en

ine is hot.

[EWA15162]

NOTICE:

If coolant is not

availa

le, use

istille

water or

soft tap water instea

. Do not

use har

water or salt water

since it is harmful to the en

ine.

If water has

een use

instea

of coolant, replace it with cool-
ant as soon as possi

le, other-

wise the coolin

system will not

e protecte

ainst frost an

corrosion. If water has

een

1. Coolant level check window
2. Maximum level mark
3. Minimum level mark

1. Floorboard mat

2
3

1. Coolant reservoir cover

UB5X10E0.book Page 14 Thursday, May 27, 2021 8:55 AM

Summary of Contents for XMAX 2022



























































































































Search results

Summary of Contents for XMAX 2022

Reviews:

Related manuals for XMAX 2022

Brands by name

Popular brands

Yamaha XMAX 2022, Owner'S Manual

Search results

Summary of Contents for XMAX 2022

Reviews:

Related manuals for XMAX 2022

Brands by name

Popular brands