Yamaha WR450FB 2012 Owner'S Service Manual Download Page 113 | Manualshive

Page: 113 / 392

background image

PERIODIC MAINTENANCE

3-22

TIP

Be sure to tighten the spokes before and after
break-in.

EAS1DX3104

CHECKING THE TIRES

To maximize the performance, durability, and
safe operation of your motorcycle, note the fol-
lowing points regarding the specified tires.

Tire air pressure

The tire air pressure should be checked and, if
necessary, adjusted before each ride.

EWA1DX3001

WARNING

Operation of this vehicle with improper tire
pressure may cause severe injury or death
from loss of control.
• The tire air pressure must be checked and

adjusted on cold tires (i.e., when the tem-
perature of the tires equals the ambient
temperature).

• The tire air pressure must be adjusted in

accordance with the weight of the rider,
the riding speed, and the riding condi-
tions.

Tire inspection

The tires must be checked before each ride.

ECA1DX3001

NOTICE

• Be sure the bead stoppers are tightened.

Loose bead stoppers will cause the tire to
slip off the rim if tire pressure is too low.

• Be sure the valve stem is positioned

straight. A tilted valve stem indicates that
the tire has slipped from its original posi-
tion on the rim. Rotate the tire so that the
valve stem is positioned straight.

Tire information

This motorcycle is equipped with spoke wheels
and tube tires.
After extensive tests, only the tires listed below
have been approved for this model by Yamaha
Motor Co., Ltd.

EWA1DX3002

WARNING

• Have a Yamaha dealer replace excessively

worn tires. Operating the motorcycle with
excessively worn tires decreases riding
stability and can lead to loss of control.

• The replacement of all wheel and brake-re-

lated parts, including the tires, should be
left to a Yamaha dealer, who has the nec-
essary professional knowledge and expe-
rience.

• It is not recommended to patch a punc-

tured tube. If unavoidable, however, patch
the tube very carefully and replace it as
soon as possible with a high-quality prod-
uct.

Spoke nipple wrench (6–7)

90890-01521

YM-01521

Spoke (front/rear)

3 Nm (0.3 m·kgf, 2.2 ft·lbf)

Standard tire air pressure

Front and Rear

100 kPa (1.00 kgf/cm², 15 psi)

1

T

R

.

.

Front tire

Size

80/100-21 51M

Manufacturer/model

DUNLOP/GEOMAX MX51FG

Rear tire

Size

120/90-18 65M

Manufacturer/model

DUNLOP/GEOMAX MX51

«
...
111
112
113
114
115
...
»

Summary of Contents for WR450FB 2012









































































































































































































































































































































































































Reviews:

No comments

Related manuals for WR450FB 2012

Brand: CF MOTO Pages: 443

Brand: zeeltronic Pages: 10

Stelvio 1200 MY11 2011

Brand: MOTO GUZZI Pages: 385

Brand: MRA Pages: 6

Montana 7 Series

Brand: Garmin Pages: 24

F12R AIR 50 cc. - Euro 2

Brand: Malaguti Pages: 46

Gold Wing GL1100

Brand: Honda Pages: 356

Brand: I2M Pages: 31

Brand: hepco & becker Pages: 2

400 SUPER COMPETITION 1999

Brand: KTM Pages: 40

Brand: X-lite Pages: 80

Brand: Touratech Pages: 8

350 BULLET 1949

Brand: Royal Enfield Pages: 102

Brand: KTM Pages: 258

Brand: SCOOT AND RIDE Pages: 46

Brand: Honda Pages: 80

Brand: XPOtool Pages: 5

Brand: Interphone Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands