Yamaha WR250FM 2021 Owner'S Service Manual Download Page 326

Page: 326 / 404

COOLING SYSTEM

8-25

EAM30351

TROUBLESHOOTING

The radiator fan motor fails to turn.

TIP

Before troubleshooting, remove the following part(s):
1. Seat
2. Side cover (left)
3. Air scoop (left/right)
4. Fuel tank

1. Check the fuse.

Refer to “CHECKING THE FUSES”

on page 8-59.



Replace the fuse(s).



2. Check the battery.

Refer to “CHECKING AND

CHARGING THE BATTERY” on

page 8-60.



•

Clean the battery terminals.

•

Recharge or replace the battery.



3. Check the main relay.

Refer to “CHECKING THE RE-

LAYS” on page 8-62.



Replace the main relay.



4. Check the radiator fan motor.

Refer to “CHECKING THE RADIA-

TOR FAN MOTOR” on page 8-69.



Replace the radiator fan motor.



5. Check the radiator fan motor relay.

Refer to “CHECKING THE RE-

LAYS” on page 8-62.



Replace the radiator fan motor relay.



6. Check the coolant temperature sen-

sor.

Refer to “CHECKING THE COOL-

ANT TEMPERATURE SENSOR”

on page 8-69.



Replace the coolant temperature sensor.



7. Check the entire cooling system’s

wiring.

Refer to “CIRCUIT DIAGRAM” on

page 8-23.



Properly connect or repair the cooling sys-

tem’s wiring.



Replace the ECU.

Summary of Contents for WR250FM 2021





















































































































































































































































































































































































































Search results

Summary of Contents for WR250FM 2021

Reviews:

Related manuals for WR250FM 2021

Brands by name

Popular brands

Yamaha WR250FM 2021, Owner'S Service Manual

Search results

Summary of Contents for WR250FM 2021

Reviews:

Related manuals for WR250FM 2021

Brands by name

Popular brands