manualshive.com logo in svg

Yamaha WR250FM 2021, Owner'S Service Manual


Share
Download
background image

ELECTRICAL COMPONENTS

8-69

a. Connect the digital circuit tester (

) to the

resistor as shown.

b. Measure the resistance of the resistor.

EAM30302

CHECKING THE RADIATOR FAN MOTOR

1. Check:

•

Radiator fan motor
Faulty/rough movement 

 Replace.

a. Disconnect the radiator fan motor coupler

from the wire harness.

b. Connect the battery (DC 12 V) as shown.

c. Measure the radiator fan motor move-

ment.

EAM30303

CHECKING THE COOLANT TEMPERATURE 

SENSOR

1. Remove:

•

Coolant temperature sensor

WARNING

EWA14130

• Handle the coolant temperature sensor

with special care.

• Never subject the coolant temperature sen-

sor to strong shocks. If the coolant temper-

ature sensor is dropped, replace it.

2. Check:

•

Coolant temperature sensor resistance
Out of specification 

 Replace.

a. Connect the digital circuit tester (

) to the

coolant temperature sensor.

b. Immerse the coolant temperature sensor

in a container filled with coolant.

TIP

Make sure the coolant temperature sensor ter-
minals do not get wet.

c. Place a thermometer in the coolant.

Resistor resistance

64.6–71.4 

Digital circuit tester (CD732)

90890-03243

Model 88 Multimeter with tachom-

eter

YU-A1927

•

Positive tester probe 

Black “1”

•

Negative tester probe 

Black “2”

•

Positive battery terminal 

Blue “1”

•

Negative battery terminal 

Black “2”

1

2

1

2

12V

L

B

Coolant temperature sensor re-

sistance

2513–2777 

 at 20 

C (2513–

2777 

 at 68 

F)

Coolant temperature sensor re-

sistance

210–221 

 at 100 

C (210–221 

 

at 212 

F)

Digital circuit tester (CD732)

90890-03243

Model 88 Multimeter with tachom-

eter

YU-A1927

•

Positive tester probe 

Green/White “1”

•

Negative tester probe 

Black/Blue “2”

1

2

G/

W

B/L

B/L

G/

W

Summary of Contents for WR250FM 2021





















































































































































































































































































































































































































Reviews:

No comments

Related manuals for WR250FM 2021

3M 600 Series User Instructions preview
600 Series
Brand: 3M Pages: 26
BV Powersports Off-Road Mini Owner'S/Operator'S Manual preview
Off-Road Mini
Brand: BV Powersports Pages: 40
NewMar BAY STAR 2017 Owner'S Manual preview
BAY STAR 2017
Brand: NewMar Pages: 116
GAS GAS Pampera Service Manual preview
Pampera
Brand: GAS GAS Pages: 34
Triumph Sprint RS Service Manual preview
Sprint RS
Brand: Triumph Pages: 410
R&G ECC0364R Fitting Instructions Manual preview
ECC0364R
Brand: R&G Pages: 6
Honda Z50R 1979 Manual preview
Z50R 1979
Brand: Honda Pages: 100
Ohlins FGR 156 Mounting Instructions preview
FGR 156
Brand: Ohlins Pages: 8
BMW K 1600 GTL Rider'S Manual preview
K 1600 GTL
Brand: BMW Pages: 176
R&G LP0107BK Fitting Instructions Manual preview
LP0107BK
Brand: R&G Pages: 14
Honda VFR400R Service Manual preview
VFR400R
Brand: Honda Pages: 41
R&G BLP0097BK Fitting Instructions Manual preview
BLP0097BK
Brand: R&G Pages: 8
Honda VTR250 Workshop Manual preview
VTR250
Brand: Honda Pages: 330
Yamaha KODIAK YFM70KDXM Owner'S Manual preview
KODIAK YFM70KDXM
Brand: Yamaha Pages: 180
Yamaha YFM700R Owner'S Manual preview
YFM700R
Brand: Yamaha Pages: 156
Yamaha RAPTOR 700R 2022 Owner'S Manual preview
RAPTOR 700R 2022
Brand: Yamaha Pages: 160
Arai GP-6S Operation Instructions preview
GP-6S
Brand: Arai Pages: 2
Fekon 150-14 Owner'S Manual preview
150-14
Brand: Fekon Pages: 24

Brands by name

Popular brands

Load more brands