manualshive.com logo in svg

Yamaha WR250FM 2021, Owner'S Service Manual


Share
Download
background image

GENERAL CHASSIS

4-4

EAM30016

REMOVING THE SEAT

TIP

The fuel tank cap cover and the seat are coupled
with each other with a plastic band.
When removing the seat, always remove the
fuel tank cap cover beforehand.

1. Remove:

•

Fuel tank cap cover “1”
Refer to “FUEL TANK CAP” on page 1-22.

2. Remove:

•

Seat “1”

EAM30458

INSTALLING THE AIR SCOOP

1. Install:

•

Air scoop (left “1”/right)

TIP

After inserting the projection “a” on the air scoop
(left/right) into the hole “b” in the air filter case, in-
serting the grooves “c” into the ribs “d” of the air
filter case, and inserting the projection “e” into
the slot “f” in the air filter case, install the air
scoop and secure it with the bolts.

EAM30459

REMOVING THE SIDE COVER

1. Remove:

•

Side cover (right) “1”

TIP

Remove the side cover (right) from the vehicle
by removing the bolts and sliding it as shown.

EAM30460

INSTALLING THE SIDE COVER

1. Install:

•

Side cover (right) “1”

TIP

•

Install the side cover (right) by sliding it as
shown and secure it with the bolts to fit it to the
vehicle.

•

Install the side cover (right) so that the rib is lo-
cated under the rib of the rear fender.

1

1

a. Projection
b. Slot

1

c

d

d

d

e

ff

a

f

b

1

1

1

b

b

a

a

Summary of Contents for WR250FM 2021





















































































































































































































































































































































































































Reviews:

No comments

Related manuals for WR250FM 2021

Würth 0984 700 400 Manual preview
0984 700 400
Brand: Würth Pages: 188
JIMS MILWAUKEE-EIGHT 5833 Instruction Sheet preview
MILWAUKEE-EIGHT 5833
Brand: JIMS Pages: 10
N-Com SPCOM00000069 Quick Start Manual preview
SPCOM00000069
Brand: N-Com Pages: 2
PIAGGIO NRG 50 User Manual preview
NRG 50
Brand: PIAGGIO Pages: 275
hepco & becker 6504518 01 01 Manual preview
6504518 01 01
Brand: hepco & becker Pages: 5
SPmoto Motorcycle User Manual preview
Motorcycle
Brand: SPmoto Pages: 92
Beta RR 4T - 250 Workshop Manual preview
RR 4T - 250
Brand: Beta Pages: 196
Beta RR 390 Manual preview
RR 390
Brand: Beta Pages: 360
APRILIA RS4 125 Service Manual preview
RS4 125
Brand: APRILIA Pages: 155
APRILIA PEGASO 650 STRADA Service Station Manual preview
PEGASO 650 STRADA
Brand: APRILIA Pages: 236
Rothewald 10010259 Instructions For Use Manual preview
10010259
Brand: Rothewald Pages: 27
Triumph Trophy Handbook preview
Trophy
Brand: Triumph Pages: 180
KTM 2010 1190 RC8 Owner'S Manual preview
2010 1190 RC8
Brand: KTM Pages: 258
Kabuto AERO-K1 Instruction Manual preview
AERO-K1
Brand: Kabuto Pages: 21
National Cycle ZTechnik VStream R1200RS Manual preview
ZTechnik VStream R1200RS
Brand: National Cycle Pages: 3
NZI Helmets Helix Owner'S Manual preview
Helix
Brand: NZI Helmets Pages: 9
KTM 690 Duke CN 2017 Setup Instructions preview
690 Duke CN 2017
Brand: KTM Pages: 16
KTM 690 Duke CN 2016 Setup Instructions preview
690 Duke CN 2016
Brand: KTM Pages: 15

Brands by name

Popular brands

Load more brands