Yamaha WOLVERINE 350 YFM35XY Owner'S Manual Download Page 88

Page: 88 / 128

8-17

NOTICE

ECB00420

Be sure no foreign material enters the final
gear case.

7. Install the oil filler bolt, and then tighten it to the

specified torque.

8. Check the final gear case for oil leakage. If oil

is leaking, check for the cause.

9. Install the final gear case guard by installing

the bolts and tightening them to the specified
torque.

EBU23645

Cleaning the air filter element

The air filter element should be cleaned at the in-
tervals specified in the periodic maintenance and
lubrication chart. Clean or, if necessary, replace
the air filter element more frequently if you are
riding in unusually wet or dusty areas.

1. Final gear oil
2. Final gear oil filler bolt

3. Correct oil level

Recommended final gear oil:

See page 10-1.

Tightening torque:

Final gear oil filler bolt:

23 Nm (2.3 m·kgf, 17 ft·lbf)

Tightening torque:

Final gear case guard bolt:

16 Nm (1.6 m·kgf, 11 ft·lbf)

U3D563E0.book Page 17 Monday, May 12, 2008 11:12 AM

Summary of Contents for WOLVERINE 350 YFM35XY

































































































































Search results

Summary of Contents for WOLVERINE 350 YFM35XY

Reviews:

Yamaha WOLVERINE 350 YFM35XY, Owner'S Manual, Page: 88 / 128

Search results

Summary of Contents for WOLVERINE 350 YFM35XY

Reviews: