Yamaha WOLVERINE 350 YFM35XY Owner'S Manual Download Page 119

Page: 119 / 128

10-1

EBU25960

SPECIFICATIONS

Dimensions:

Overall length:

1978 mm (77.9 in)

Overall width:

1063 mm (41.9 in)

Overall height:

1095 mm (43.1 in)

Seat height:

840 mm (33.1 in)

Wheelbase:

1233 mm (48.5 in)

Ground clearance:

220 mm (8.7 in)

Minimum turning radius:

3000 mm (118 in)

Weight:

With oil and fuel:

229.0 kg (505 lb)

Noise and vibration level:

Noise level (77/311/EEC):

79.4 dB(A)

Vibration on seat (EN1032, ISO5008):

Will not exceed 0.5 m/s²

Vibration on handlebar (EN1032, ISO5008):

Will not exceed 2.5 m/s²

Engine:

Engine type:

Air cooled 4-stroke, SOHC

Cylinder arrangement:

Forward-inclined single cylinder

Displacement:

348.0 cm³

Bore

stroke:

83.0

64.5 mm (3.27

2.54 in)

Compression ratio:

9.20 :1

Starting system:

Electric starter

Lubrication system:

Wet sump

U3D563E0.book Page 1 Monday, May 12, 2008 11:12 AM

Summary of Contents for WOLVERINE 350 YFM35XY

































































































































Search results

Summary of Contents for WOLVERINE 350 YFM35XY

Reviews:

Yamaha WOLVERINE 350 YFM35XY, Owner'S Manual, Page: 119 / 128

Search results

Summary of Contents for WOLVERINE 350 YFM35XY

Reviews: