Yamaha WaveRunner VX Deluxe 2007 Owner'S/Operator'S Manual Download Page 74

Page: 74 / 96

Maintenance and care

water passages by alternately squeezing
and releasing the throttle lever for 10 to
15 seconds.

(8) Stop the engine.
(9) Remove the garden hose adapter and in-

stall the flushing hose connector cap.

EJU33620

Lubrication

WARNING

EWJ00260

Do not spray flammable rust inhibitor
products on engine surfaces while the en-
gine is hot. The sprayed substance or pro-
pellants could catch fire.

(1) Remove the seat. (See page 26 for seat

removal and installation procedures.)

(2) Loosen the clamp screw and disconnect

the air intake duct.

(3) Spray a rust inhibitor into the intake open-

ing for 3 seconds.

(4) Connect the air intake duct and tighten

the clamp screw.

(5) Start the engine in a well-ventilated area

and let it run at idle for 15 seconds.

CAUTION:

ECJ00160

Do not run the engine for more than 15
seconds, otherwise the engine could over-
heat.

(6) Lubricate all cables such as the throttle

and steering cables.

NOTE:

Use a suitable marine grease applicator to
pressure-lubricate the cables and purge out
any moisture between the inner and outer ca-
bles.

(7) Lubricate the areas of the watercraft

specified in “Lubrication points” on page
76.

EJU33670

Fuel system

WARNING

EWJ00280

GASOLINE AND ITS VAPORS ARE HIGH-
LY FLAMMABLE AND EXPLOSIVE!

Clamp screw

Air intake duct

Intake opening

UF1K72E0.book Page 67 Wednesday, August 2, 2006 10:43 AM

Summary of Contents for WaveRunner VX Deluxe 2007

































































































Search results

Summary of Contents for WaveRunner VX Deluxe 2007

Reviews:

Related manuals for WaveRunner VX Deluxe 2007

Brands by name

Popular brands

Yamaha WaveRunner VX Deluxe 2007, Owner'S/Operator'S Manual

Search results

Summary of Contents for WaveRunner VX Deluxe 2007

Reviews:

Related manuals for WaveRunner VX Deluxe 2007

Brands by name

Popular brands