manualshive.com logo in svg

Yamaha WaveRunner VX 2015, Operator'S Manual, Page: 92 / 108

Share
Download
Yamaha WaveRunner VX 2015 Operator'S Manual Download Page 92

Care and storage

86

(2) Loosen the clamp screw and disconnect

the air intake duct.

(3) Spray a rust inhibitor into the intake

opening for 3 seconds. 

WARNING! Do

not spray flammable rust inhibitor
products on engine surfaces while the
engine is hot. The sprayed substance
or propellants could catch fire.

 [EWJ00262]

(4) Connect the air intake duct and securely

tighten the clamp screw.

TIP:

Confirm that the air intake duct is inserted
until it touches the protrusion.

After tightening the clamp screw, confirm
that the hose holder is attached in its origi-
nal position.

(5) Make sure that the area around the wa-

tercraft is clear, and then start the engine
in a well-ventilated area and let it run at
idle for 15 seconds. (See page 28 for in-
formation on starting the engine.)

(6) Stop the engine.
(7) Securely install the seats in their original

positions.

1

Air intake duct

2

Clamp screw

1

Intake opening

2

1

1

UF2X70E0.book  Page 86  Wednesday, September 17, 2014  8:52 AM

Summary of Contents for WaveRunner VX 2015













































































































Reviews:

No comments