3 9
MIDI DATA FORMAT
1. Tone Generator
1.1 MIDI reception/transmission block diagram
(MIDI reception condition) 1/2
$FE ACTIVE SENSING
$8n NOTE OFF
$9n NOTE ON/OFF
$Bn,$xx Each controller
$Bn,$xx
$Bn,$20
$Bn,$00 BANK SELECT
$Cn PROGRAM CHANGE
$Dn AFTER TOUCH
$En PITCH BENDER
<each ch>
<each ch>
<each ch>
<each ch>
<each ch>
<each ch>
MIDI
sw1
sw2
NOTES:
sw1: Setting MIDI Program Change to "on" turns sw1 on.
sw2: Settings other than MIDI Program Change "off" turns sw2 on.
(MIDI reception condition) 2/2
Dev No = Device Number
MIDI-Datenformat
Données de Format MIDI
$F0,$43,$10,$33,$0F,$00
$F0,$7E,$cc,$06,$01
$F0,$7E,$7F,$09,$01
$F0,$7F,$7F,$04,$01
$F0,$43,$0n,$7A
(LM__0147VC)
$F0,$43,$0n,$7A
(LM__0147DR)
$F0,$43,$0n,$7A
(LM__0147EL)
$F0,$43,$0n,$7A
(LM__0147EM)
$F0,$43,$0n,$7A
(LM__0147MU)
$F0,$43,$0n,$7A
(LM__0147SY)
$F0,$43,$1n,$33,$xx
$F0,$43,$1n,$04,$40
$F0,$43,$2n,$7A
(LM__0147VC)
$F0,$43,$2n,$7A
(LM__0147DR)
$F0,$43,$2n,$7A
(LM__0147EL)
$F0,$43,$2n,$7A
(LM__0147EM)
$F0,$43,$2n,$7A
(LM__0147MU)
$F0,$43,$2n,$7A
(LM__0147SY)
$F0,$43,$2n,$7A
(LM__0147WH)
MIDI
<Dev No>
≠
off
SW REMOTE
IDENTIFY REQUEST
GENERAL MIDI MODE ON
MIDI MASTER VOLUME
NORMAL VOICE bulk
DRUM VOICE bulk
ELEMENT bulk
ELEMENT Map bulk
SONG/MULTI bulk
SYNTH SETUP bulk
PARAMETER CHANGE
PARAMETER CHANGE
(Master Tuning)
same as DX1 format
NORMAL VOICE bulk D.req.
DRUM VOICE bulk D.req.
ELEMENT bulk D.req.
ELEMENT Map bulk D.req.
SONG/MULTI bulk D.req.
SYNTH SETUP bulk D.req.
WAVE HEADER bulk D.req.
(MIDI transmission condition)
NOTES:
sw1: Setting MIDI Program Change to "on" turns sw1 on.
sw2: Settings other than MIDI Program Change "off" turns sw2 on.
1.2 Channel Message
1.2.1 Transmission
1.2.1.1 Note on/off
Transmission note range = C-2(0)...G8(127)
Velocity range
= 1...127
1.2.1.2 Control change
Control change is output via MIDI when the following controllers are used.
ACTIVE SENSING
NOTE ON/OFF
MODULATION WHEEL
FOOT CONTROL
VOLUME
SUSTAIN SWITCH
DATA ENTRY
AFTER TOUCH
PITCH BEND
BANK SELECT
PROGRAM CHANGE
VOICE bulk
ELEMENT bulk
SONG/MULTI bulk
SYNTH SETUP bulk
PARAMETER CHANGE
IDENTIFY REPLY
$9n
$Bn,
$Bn,
$Bn,
$Bn,
$Bn,
$Dn
$En
$Bn,
$Cn
$01
$04
$07
$40
$06
$00
$20
<Dev No>
≠
off
Program Change
sw1 on
Program Change
sw2 on
MIDI
<T ch>
transmit
ch
ctrl#
1
4
7
11
64
1
〜
119
parameter
Modulation Wheel
Foot Controller
Foot Volume
Expression
Sustain Switch
Continuous Slider
data rng
0
〜
127
0
〜
127
0
〜
127
0
〜
127
0
，
127
0
〜
127
