background image

INSTRUMENT AND CONTROL FUNCTIONS

3-6

3

CAUTION:

ECA10070

Immediately wipe off spilled fuel
with a clean, dry, soft cloth, since
fuel may deteriorate painted surfac-
es or plastic parts.

EAU13300

CAUTION:

ECA11400

Use only unleaded gasoline. The use
of leaded gasoline will cause severe
damage to internal engine parts,
such as the valves and piston rings,
as well as to the exhaust system.

Your Yamaha engine has been de-
signed to use regular unleaded gaso-
line with a pump octane number

[(R+M)/2] of 86 or higher, or a research
octane number of 91 or higher. If
knocking (or pinging) occurs, use a
gasoline of a different brand or premi-
um unleaded fuel. Use of unleaded fuel
will extend spark plug life and reduce
maintenance costs.

Gasohol

There are two types of gasohol: gaso-
hol containing ethanol and that contain-
ing methanol. Gasohol containing
ethanol can be used if the ethanol con-
tent does not exceed 10%. Gasohol
containing methanol is not recom-
mended by Yamaha because it can
cause damage to the fuel system or ve-
hicle performance problems.

EAU13580

Fuel cock 

This model is equipped with a negative
pressure fuel cock. The fuel cock sup-
plies fuel from the tank to the carburetor
while also filtering it.
The fuel cock lever positions are ex-
plained as follows and shown in the il-
lustrations.

ON

With the fuel cock lever in this position,
fuel flows to the carburetor when the
engine is running. Turn the fuel cock le-
ver to this position when starting the en-
gine and riding.

Recommended fuel:

UNLEADED GASOLINE ONLY

Fuel tank capacity:

9.2 L (2.43 US gal) (2.02 Imp.gal) 
(CAL)
9.5 L (2.51 US gal) (2.09 Imp.gal) 
(U49)

Fuel reserve amount:

2.6 L (0.69 US gal) (0.57 Imp.gal)

1. Arrow mark positioned over “ON”

U2UJ1DE0.book  Page 6  Thursday, May 13, 2004  11:59 PM

Summary of Contents for Virago XV250 2004
































































































Reviews: