Yamaha VF200 Owner'S Manual Download

Page: 97 / 120

Maintenance

Checkpoints



Check each of the propeller blades for ero-
sion from cavitation or ventilation, and oth-
er damage.



Check the propeller shaft for damage.



Check the splines for wear and damage.



Check for fish line tangled around the pro-
peller shaft.

EMU42632

Removing propeller

1. Straighten the cotter pin and pull it out

using a pair of pliers.

2. Remove the propeller nut, washer, and

spacer.

WARNING! Do not use your

hand to hold the propeller when loos-
ening the propeller nut.

[EWM01891]

3. Remove the propeller, spacer (if

equipped), and thrust washer.

EMU46220

Installing propeller

NOTICE

ECM00502

Make sure to use a new cotter pin and
bend the ends over securely. Otherwise,
the propeller could come off during oper-
ation and be lost.

1. Apply Yamalube Marine Grease to the

propeller shaft.

2. Install the thrust washer, spacer (if

equipped), and propeller on the propel-
ler shaft.

NOTICE:

Make sure to install

the thrust washer before installing
the propeller. Otherwise, the lower
case and propeller boss could be
damaged.

[ECM01882]

3. Install the spacer, washer, and propeller

nut. Tighten the propeller nut to the
specified torque.

1. Propeller shaft

ZMU06953

ZMU06954

1. Cotter pin
2. Propeller nut
3. Washer
4. Spacer
5. Propeller
6. Spacer
7. Thrust washer

4 3

ZMU06955

6CB-9-3B-1E0.book 91 ページ２０１７年１１月１６日　木曜日　午後５時２９分

2019 Yamaha Motor Corporation, U.S.A.

Summary of Contents for VF200

























































































































Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands

Yamaha VF200, Owner'S Manual

Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands