UD-Stomp
28
ERROR MESSAGES
INPUT Sensitivity
INPUT Sensitivity
INPUT Sensitivity
INPUT Sensitivity
INPUT Sensitivity
INPUT Sensitivity
INPUT Sensitivity
INPUT Sensitivity
INPUT Sensitivity
INPUT Sensitivity
INPUT Sensitivity
INPUT Sensitivity
INPUT Sensitivity
INPUT Sensitivity
INPUT Sensitivity
NOISE LEVEL
NOISE LEVEL
NOISE LEVEL
NOISE LEVEL
DISTORTION FACTOR
DISTORTION FACTOR
DISTORTION FACTOR
DISTORTION FACTOR
INPUT Sensitivity
ITEM
INPUT
OUTPUT
JK101(INPUT) -5dBm(1KHz)
JK101(INPUT) -5dBm(10KHz)
JK101(INPUT) -5dBm(100Hz)
JK101(INPUT) -25dBm(100Hz)
JK101(INPUT) -25dBm(10KHz)
JK101(INPUT) -25dBm(1KHz)
JK101(INPUT) -5dBm(1KHz)
JK101(INPUT) -5dBm(10KHz)
JK101(INPUT) -5dBm(100Hz)
JK101(INPUT) -25dBm(100Hz)
JK101(INPUT) -25dBm(10KHz)
JK101(INPUT) -25dBm(1KHz)
JK101(INPUT) -35dBm(1KHz) HIGH/LOW SW ON
JK101(INPUT) -35dBm(10KHz) HIGH/LOW SW ON
JK101(INPUT) -35dBm(100Hz) HIGH/LOW SW ON after operation OFF
Disconnect the jack of JK101 (INPUT), without filter
Disconnect the jack of JK101 (INPUT), without filter
Disconnect the jack of JK101 (INPUT), without filter
Disconnect the jack of JK101 (INPUT), without filter
JK101(INPUT) -5dBm (1KHz)
JK101(INPUT) -25dBm (1KHz)
JK101(INPUT) -5dBm (1KHz)
JK101(INPUT) -25dBm (1KHz)
JK101(INPUT) -15dBm (1KHz)
JK103(OUT L/MONO)+1.0dBm
±
3dB
JK103(OUT L/MONO)+1.0dBm
±
3dB
JK103(OUT L/MONO)+1.0dBm
±
3dB
JK104(OUT R)-1.0dBm
±
3dB
JK104(OUT R)-1.0dBm
±
3dB
JK104(OUT R)-1.0dBm
±
3dB
JK102(HP L)-0.5dBm
±
3dB
JK102(HP L)-0.5dBm
±
3dB
JK102(HP L)-1.5dBm
±
3dB
JK102(HP R)-3.5dBm
±
3dB
JK102(HP R)-2.5dBm
±
3dB
JK102(HP R)-2.5dBm
±
3dB
JK104(OUT R)-0.5dBm
±
3dB
JK104(OUT R)-0.5dBm
±
3dB
JK104(OUT R)-0.5dBm
±
3dB
JK103(OUT L/MONO)-45dBm or less
JK104(OUT R)-45dBm or less
JK102(HP L)-45dBm or less
JK102(HP R)-45dBm or less
JK103(OUT L/MONO) 0.5% or less
JK104(OUT R) 0.5% or less
JK102(HP L) 0.5% or less
JK102(HP R) 0.5% or less
JK2(Digital Out) Lch:-18dBm
±
3dB, Rch:
±
0dBm
±
3dB
F.
CHEKING OF THE ROM VERSION
While pressing the DOWN and UTILITY switches, turn
on the POWER switch. The model name “Ud.S” is
Table1
displayed for about 2 seconds. As the version number
“1.00” (each * representing a number) appears after that,
check it. Then the mode will return to the normal mode.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
If an error occurs during operation, one of the following error message numbers will appear in the display.
Stop operation of the device and follow the proper solution described below.
E 1
: MIDI Receive Buffer Full
CAUSE:
Too much MIDI data is being received at one time.
SOLUTION: Try reducing the amount of data being sent or, break the data into smaller blocks.
E 2
: Communication Error.
CAUSE:
An abnormality is detected during MIDI communications.
SOLUTION: Check all connections, etc. and try again.
E 3
: Bulk Receive Check Sum Error.
CAUSE:
The check sum does not match the received MIDI bulk data.
SOLUTION: Check all connections and data, and try again.
E 4
: Bulk Receive Data Abnormality.
CAUSE:
An abnormality is detected in the received MIDI bulk data.
SOLUTION: Check all connections and data, and try again.
E 5
: Backup Battery Error.
CAUSE:
Backup battery power is depleted.
SOLUTION: Continued use of the device will result in the loss of data.
Summary of Contents for UD-Stomp
